Enterasys Networks 2000 manual System image add IPaddr-of-TFTP-host image-file-name

Page 73

Loading System Image Firmware

2.Copy the firmware upgrade you want to install onto a TFTP server that the XP-2000 can access. (Use the ping command to verify that the XP can reach the TFTP server.)

3.Use the following command to copy the firmware upgrade onto the internal flash chip in the XP-2000:

system image add <IPaddr-of-TFTP-host> <image-file-name>

Here is an example:

xp-1#system image add tftp-server 10.50.11.12 file-name /images/E9050-image Downloading image '/images/E9050-image' from host '10.50.11.12'

to local image E9050-image (takes a while) . . .

download: done save:

kernel: 100%

images/ssr_wan: 100%

images/ssr_are: 100%

images/ssr_fddi: 100%

images/ssr_atm155_sar: 100%

images/ssr_atm155_fpga_400: 100% done

Image checksum validated.

%SYS-I-BOOTADDED, Image 'E9050-image' added.

4.Enter the system image list command to verify that the new image exists on the internal flash chip, as shown in the following example:

xp-1#system image list

Images currently available on Master CM: E9050-image (version E9.0.5.0)

**Warning: No local image is selected for next reboot on this CM. Consider using the 'system image choose <imagename>' command to choose an image for this CM. If you do not, the XP will attempt to boot by first searching the bootsource variable in nvram. When this variable is not set, you will be sent to the boot prom prompt. When this variable is set, the XP will attempt to boot from the image set. If this fails, the XP will search for a single image on the flash.

If a single image is found, the XP will use it to boot.

But if a single image is not found (perhaps no images are on the flash or perhaps more than one image is on the flash) the XP will send you to the boot prom prompt.

5.Use the following command to select the image file the XP-2000 will use the next time you reboot the switch.

system image choose <file-name>

Enterasys X-Pedition 2000 Getting Started Guide

57

Image 73

Contents 2000 Page FCC Notice Enterasys X-Pedition 2000 Getting Started Guide Enterasys NETWORKS, INC Program License Agreement Enterasys X-Pedition 2000 Getting Started Guide Enterasys X-Pedition 2000 Getting Started Guide Vii Declaration of Conformity Contents Hardware Installation Index Appendix a TroubleshootingContents Xii Enterasys X-Pedition 2000 Getting Started Guide What’s New How to Use this GuideWho should Read this Guide? If You Want To SeeGetting Help Related DocumentationFor Information About See Preface Preface Xvi Enterasys X-Pedition 2000 Getting Started Guide Specifications Chapter Features OverviewRmon IPX RIP, SAPSnmp TCP/UDP Services FeaturesTCP/UDP services TCP Port UDP Port Description LLCPort and Protocol VLANs BridgingRouting IP Multicast Routing IP RoutingIPX Routing Security Layer-4 SwitchingStatistics Quality of ServiceManagement Platforms VlanChassis Hardware OverviewBoot Flash Motherboard FeaturesExternal Controls Status LEDs LED Label DescriptionFans Power SuppliesRAM Memory 10/100BASE-TX Expansion Module Expansion ModulesLEDs Cabling and Connector Specifications100BASE-TX expansion module LEDs Front panel of 100BASE-FX expansion module 100BASE-FX Expansion Module1000BASE-SX Expansion Module BASE-FX expansion module LEDsBASE-SX expansion module LEDs Front panel of 1000BASE-LX expansion module 1000BASE-LX Expansion ModuleBASE-LX expansion module LEDs Front panel of Dual Serial WAN expansion module Dual Serial and Quad Serial C/CE Expansion ModulesDual Serial and Quad Serial C/CE WAN expansion module LEDs Dual Hssi Line Card Port Type SpecificationHssi LED Page Preventing Injury Safety ConsiderationsInstalling the Hardware Hardware SpecificationsXP-2000 physical and environmental specifications Preventing Equipment DamageVerifying Your Shipment Table-Top Installation Installing the ChassisRack Mount Installation Installing the XP-2000 chassis in an equipment rack Installing an Expansion Module Connecting Power to the ChassisInstalling the new face plate view from inside chassis Front of XP-2000 Nteras ys Net works Attaching the Console Management CablesPlugging into the XP-2000’s serial DB-9 DCE port Connecting to the Serial PortPlugging into the XP-2000’s 10/100Base-TX port Connecting to the 10/100Base-TX PortRXD receive data TXD transmit data Attaching Port CablesPlugging an ethernet cable into a 10/100BASE-TX port 100BASE-TX RJ-45 connector 1000BASE-SX and 1000BASE-LX Expansion Modules LFH-60 high density connector pin assignments Pin Signal P2GND P1TXCA P2CTSB P1RXCA P1GND P1TXDBP2SCTEB P1LLA P2RXCA P1GND P2SCTEA P1SHIELD Pin Signal Pin Hssi connector Page Powering On and Booting the Firmware Chapter Firmware Installation SetupAccess Modes Starting the Command Line InterfaceSome commonly used CLI commands Key sequence Command Basic Line Editing CommandsHere is an example Setting Basic System InformationEnter yes or y to activate the changes Enter the copy active to startup command Setting Up Snmp Community StringsSetting Up Snmp Community Strings READ-WRITE Xp-1#system show active-config Setting Up PasswordsXp-1#ping Setting the DNS Domain Name and AddressSystem set dns server IP-address IP-address IP-address Setting Syslog Parameters Setting Syslog Parameters Ping IP-addr Loading System Image Firmware System image add IPaddr-of-TFTP-host image-file-name Enter the system image list command to verify the change Xp-1#system promimage upgrade 10.50.11.12 prom2 Loading Boot Prom FirmwareUpgrading the VFS Viewing the Current Configuration Activating the Configuration Commands in the ScratchpadCommand like stp enable et.*.* would be displayed as follows If you experience this difficulty Try this remedy Appendix a TroubleshootingUse the procedure in Activating the Configuration Appendix B Technical Support Getting Help Dvmrp NumericsIPX SAP IgmpNvram UDP Layer-4 flow 6 services User mode VLANsIndex Enterasys X-Pedition 2000 Getting Started Guide

Related manuals

Manual 188 pages 39.25 Kb