Enterasys Networks FN 100 manual Virus Disclaimer

Page 3

Notice

Enterasys Networks reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Virus Disclaimer

Enterasys has tested its software with current virus checking technologies. However, because no anti- virus system is 100% reliable, we strongly caution you to write protect and then verify that the Licensed Software, prior to installing it, is virus-free with an anti-virus system in which you have confidence.

Enterasys Networks makes no representations or warranties to the effect that the Licensed Software is virus-free.

Copyright © 2000 by Enterasys Networks. All rights reserved.

Printed in the United States of America.

Order Number: 9031897-03 April 2000

Enterasys Networks.

P.O. Box 5005

Rochester, NH 03866-5005

Enterasys, NetSight, and Matrix E7 are trademarks of Enterasys Networks.

Cabletron Systems, SPECTRUM, BRIM, DNI, FNB, INA, Integrated Network Architecture, LANVIEW, LANVIEW Secure, Multi Media Access Center, MiniMMAC, and TRMM are registered trademarks, and Bridge/Router Interface Modules, BRIM-A100,CRBRIM-W/E,CRXMIM, CXRMIM, Desktop Network Interface, Distributed LAN Monitoring, Distributed Network Server, DLM, DNSMIM, E1000, E2000, E3000, EFDMIM, EMM-E6,EMME, EPIM, EPIM-3PS,EPIM-A,EPIM-C,EPIM-F1,EPIM-F2,EPIM-F3,EPIM-T,EPIM-T1,EPIM-X,ESXMIM, ETSMIM, ETWMIM, FDCMIM-04,FDCMIM-08,FDMMIM, FDMMIM-04,Flexible Network Bus, FOMIM, FORMIM, HubSTACK, IRBM, IRM, IRM-2,IRM-3,Media Interface Module, MicroMMAC, MIM, MMAC, MMAC-3,MMAC-3FNB,MMAC-5,MMAC-5FNB,MMAC-8,MMAC-8FNB,MMAC-M8FNB,MMAC-Plus,MRX, MRXI, MRXI-24,MultiChannel, NB20E, NB25E, NB30, NB35, NBR-220/420/620,RMIM, SecureFast Packet Switching, SFPS, SPECTRUM Element Manager, SPECTRUM for Open Systems, SPIM-A,SPIM-C,SPIM-F1,SPIM-F2,SPIM-T,SPIM-T1,TPMIM, TPMIM-22,TPMIM-T1,TPRMIM, TPRMIM-36,TPT-T,TRBMIM, TRMM-2,TRMMIM, and TRXI are trademarks of Cabletron Systems, Inc.

i

Image 3
Contents FN 100 User’s Guide Page Virus Disclaimer Page Restricted Rights Notice Page Contents Chapter Using FN100 Trunking Chapter Workgroup ConfigurationIndex Introduction Using the FN100 User’s GuideSoftware Conventions Related ManualsLocation Common FN100 Window FieldsDevice Name IP AddressUptime Using the MouseMAC Address Port NumberUsing Window Buttons Using On-line Help Getting HelpGetting Help from the Global Technical Assistance Center Introduction Introduction Getting Help FN100 Chassis View Viewing Chassis Information Front Panel InformationConnection Status Time Boot PromPort Status FirmwareDevice Menu Menu StructurePort Status Menu Utilities Menu Help MenuPort Menus FN100 Port Status Displays Selecting a Port Status ViewStatus Speed ErrorsLoad MappingChassis Manager Window TypePort Status Color Codes Viewing Hardware Types Viewing the Device TypeViewing the Port Description Managing the Hub Using Device Find Source AddressPort Instance ComponentViewing I/F Summary Information Logical Status IndexDescription Physical StatusRaw Counts Viewing Interface Detail RateNon-Unicast ErrorAddress UnicastMaking Sense of Detail Statistics Receive Errors Viewing Csmacd StatisticsAlignment Transmission Errors Enabling and Disabling Ports Collision ErrorsTo enable or disable a bridge port Performing Virtual Switching FN100 Virtual SwitchingUpdate Configuring Your Virtual Switch SettingsChange Default Switch Window Defining a Default SwitchFN100 Virtual Switching Performing Virtual Switching Using FN100 Trunking State Port Trunking WindowLast Error Rmt Bridge IdRmt IP Address Clear Link OrdinalLink Count Last ChangeEnabling and Disabling Trunking Using FN100 Trunking Port Trunking Window Workgroup Configuration Workgroup Configuration Configuring a WorkgroupDeleting a Workgroup Workgroup Configuration Configuring a Workgroup Index Index-2