Enterasys Networks FN 100 manual Restricted Rights Notice

Page 5

ANNEX, ANNEX-II, ANNEX-IIe, ANNEX-3, ANNEX-802.5, MICRO-ANNEX-XL, and MICRO- ANNEX-ELS are trademarks of Xylogics, Inc.

MAXserver and Xyplex are trademarks of Xyplex, Inc.

Restricted Rights Notice

(Applicable to licenses to the United States Government only.)

1.Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013.

Enterasys Networks, 35 Industrial Way, Rochester, New Hampshire 03867.

2.(a) This computer software is submitted with restricted rights. It may not be used, reproduced, or disclosed by the Government except as provided in paragraph (b) of this Notice or as otherwise expressly stated in the contract.

(b)This computer software may be:

(1)Used or copied for use in or with the computer or computers for which it was acquired, including use at any Government installation to which such computer or computers may be transferred;

(2)Used or copied for use in a backup computer if any computer for which it was acquired is inoperative;

(3)Reproduced for safekeeping (archives) or backup purposes;

(4)Modified, adapted, or combined with other computer software, provided that the modified, combined, or adapted portions of the derivative software incorporating restricted computer software are made subject to the same restricted rights;

(5)Disclosed to and reproduced for use by support service contractors in accordance with subparagraphs (b) (1) through (4) of this clause, provided the Government makes such disclosure or reproduction subject to these restricted rights; and

(6)Used or copied for use in or transferred to a replacement computer.

(c)Notwithstanding the foregoing, if this computer software is published copyrighted computer software, it is licensed to the Government, without disclosure prohibitions, with the minimum rights set forth in paragraph (b) of this clause.

(d)Any other rights or limitations regarding the use, duplication, or disclosure of this computer software are to be expressly stated in, or incorporated in, the contract.

(e)This Notice shall be marked on any reproduction of this computer software, in whole or in part.

iii

Image 5
Contents FN 100 User’s Guide Page Virus Disclaimer Page Restricted Rights Notice Page Contents Index Chapter Using FN100 TrunkingChapter Workgroup Configuration Introduction Using the FN100 User’s GuideSoftware Conventions Related ManualsDevice Name Common FN100 Window FieldsIP Address LocationMAC Address Using the MousePort Number UptimeUsing Window Buttons Getting Help from the Global Technical Assistance Center Using On-line HelpGetting Help Introduction Introduction Getting Help FN100 Chassis View Connection Status Viewing Chassis InformationFront Panel Information Port Status Boot PromFirmware TimeDevice Menu Menu StructurePort Status Menu Port Menus Utilities MenuHelp Menu Status FN100 Port Status DisplaysSelecting a Port Status View Load ErrorsMapping SpeedPort Status Color Codes Chassis Manager WindowType Viewing the Port Description Viewing Hardware TypesViewing the Device Type Managing the Hub Using Device Find Source AddressPort Instance ComponentViewing I/F Summary Information Description IndexPhysical Status Logical StatusRaw Counts Viewing Interface Detail RateAddress ErrorUnicast Non-UnicastMaking Sense of Detail Statistics Alignment Receive ErrorsViewing Csmacd Statistics Transmission Errors Enabling and Disabling Ports Collision ErrorsTo enable or disable a bridge port Performing Virtual Switching FN100 Virtual SwitchingUpdate Configuring Your Virtual Switch SettingsChange Default Switch Window Defining a Default SwitchFN100 Virtual Switching Performing Virtual Switching Using FN100 Trunking State Port Trunking WindowRmt IP Address Last ErrorRmt Bridge Id Link Count Link OrdinalLast Change ClearEnabling and Disabling Trunking Using FN100 Trunking Port Trunking Window Workgroup Configuration Workgroup Configuration Configuring a WorkgroupDeleting a Workgroup Workgroup Configuration Configuring a Workgroup Index Index-2