Enterasys Networks MicroMMAC-T manual Beacon Statistics, Soft Error Fields

Page 62

Token Ring Statistics

Ring Purges

Displays the number of times the active monitor has purged the ring since the network was created, or since the MicroMMAC-T was last reset. This includes the purge at the end of the active monitor selection process. The count is not reset when the active monitor changes.

Total Frames

Displays the number of frames that have been transmitted on the ring.

Total KBytes

Displays the total number of kilobytes that have been transmitted on the ring. This number is the sum of all data bytes in each frame.

Beacon Statistics

A Beacon is transmitted when a hardware error is detected on the ring, including: wire faults, frequency errors, or ring signal loss.

Note that the Longest Beacon and Last Beacon fields are read from the device (Total update), and are not subject to Delta or Cumulative update options.

Beacon States

This field lists the count of beaconing occurrences on the ring.

Longest Beacon

This field lists the duration of the longest beaconing occurrence (not subject to Delta/Cumulative update).

Last Beacon

This field provides the duration of the last beacon (not subject to

Delta/Cumulative update).

Soft Error Fields

Line Errors

Displays the total number of line errors that the management station has detected. These are recorded when a receiving station detects a data corruption in a frame that was initially transmitted as a good frame, with the E bit (error flag) set at zero (0).

A power surge on the ring (line of transmission) may cause the data portion of a frame or token to be corrupted. The frame or token then may contain a non-data bit between the data start and end delimiters, or a Frame Check Sequence (FCS) error.

3-6	Network Level Statistics

Image 62

Contents MicroMMAC-T Users Guide Page Virus Disclaimer Page Restricted Rights Notice Page Contents Contents Chapter Token Ring StatisticsIndex Chapter Token Ring AlarmsChapter Station List and Station Map Contents Viii Introduction Using This Guide IntroductionSoftware Conventions Using the MouseRelated Manuals Left Mouse Button Right Mouse Button Using Window Buttons Common MicroMMAC-T Window FieldsLocation Device NameIP Address MAC AddressGetting Help from Enterasys Global Call Center Using On-line HelpGetting Help Introduction MicroMMAC-T Chassis View Viewing Chassis Information Front Panel Information Date Menu StructureTime MicroMMAC-T Chassis View Menu Structure Device MenuPort Status Menu Network Menu Utilities MenuPort Menus Help MenuModule Menus Selecting a Port Status View Port Status DisplaysRing Port Menus Status ErrorsLoad Port Status Color Codes Port AssignmentRing Port Status Click on MIBs Supported Chassis Manager WindowViewing Hardware Types Module Type Managing the HubDevice Type Management Station Configuration Accessing the TR Management Station Configuration WindowSetting Station Name and Location Station Name Configuration WindowSpecifying Ring Management Functions Host Error Report Timer DelayEnable Beacon Recovery Inhibit Active MonitorEnable Ring Poll Recovery Viewing Network Information Selecting the RingNetwork Information Window Fields Token Ring Board Status Window Fields Ring of X Configured RingsViewing Module Status Board NumberAccessing the Ring Port Status window Viewing Ring Port StatusPort Last Wire FaultRing Port Status Window Fields Media TypeSetting the Device Date and Time Using the Media Type and Phantom Current Radio ButtonsUsing an Uninterruptable Power Supply UPS 13. Device Date Change WindowAccessing the UPS Window 14. The UPS WindowUPS Uptime Battery OutputBattery Capacity Line VoltageUsing the Test Option Resetting the DeviceSetting the UPS ID Using the Disconnect OptionEnabling and Disabling Port Mapping Enabling and Disabling Link Traps 15. The Port Map WindowSetting Token Ring Boards to Automode Enabling and Disabling Link Traps at the Board LevelEnabling and Disabling Ring Ports Enabling and Disabling PortsEnabling and Disabling Station Ports Ring Out Enable/Disable Viewing I/F Summary InformationDescription IndexType Physical StatusInterface Performance Statistics/Bar Graphs Raw CountsRate Viewing Interface DetailAddress UnicastMaking Sense of Detail Statistics Transmitted Errors /Packets Transmitted Statistics Window Features Setting Total, Delta, or Cumulative CountsViewing Elapsed, Average, and Peak Activity Levels Token Ring StatisticsSetting the Statistics Poll Interval New Timer Interval Text BoxNetwork Statistics Window Accessing the Network Statistics SelectionsNetwork Level Statistics General Information FieldsStations Inserted Ring SpeedRing Status Fields Active MonitorSoft Error Fields Beacon StatisticsAbort Sequences Burst ErrorsInternal Errors Frequency Errors Congestion ErrorsToken Errors Lost FramesNetwork Timer Statistics Window Fields Network Timer StatisticsTotal Errors KBytes Network Performance GraphsFrames Network Events Red Configuring the Network Performance GraphNetwork Performance Graph Statistics Traffic BlueFrame Size Window Total and Delta Graph DisplayUsing the Pie and Bar Radio Buttons Frame Sizes Window with Pie ChartProtocol Statistics Window Accessing the Management Station Statistics Selection Management Station StatisticsSoft Errors Fields Hard Errors Fields FC ErrorsSoft Errors Signals LostHard Errors RecoveriesLobe Wire Fault Transmitted BeaconsStation Statistics Window Accessing the Station Port MenuPort Level Statistics Link Time Station Statistics Window General FieldsStation Name Station Statistics Window Performance FieldsStation Statistics Window Soft Error Fields Station Timer Statistics Window Station Timer Statistics Window Fields Port Performance GraphsTotal Errors Red Port Performance Graph StatisticsConfiguring the Port Performance Graph Token Ring Statistics Token Ring Alarms Ring-Level Alarm LimitsAccessing the Alarm Limits Window Ring-Level Alarm Limits for Network EventsRing-Level Station Alarms Token ErrorsSetting Ring-Level Alarm Limits LineStation-Level Alarm Limits Accessing the Station Alarm Limits Window from the Port MenuToken Ring Alarms Setting Station-Level Alarm Limits Station Alarm Limits WindowToken Ring Alarms Station List and Station Map Station List WindowGeneral Fields Address ModeStation List Window Fields Number of Nodes/StationsViewing Station Statistics Station FieldsRemoving a Station from the Ring Viewing Station Timer StatisticsSetting Station Alarms Printing the Station List Using the MAC/Canonical ButtonViewing the Station Port Performance Graph Resetting Counters Station MapStation Map Window Fields Number of NodesViewing the Station Map Station Pop-up Text BoxesStation Map with Text Boxes Node AddressStation Command Menu Manipulating the Station Map Magnifying a Portion of the MapRotating the Station Map Resizing the Station Map Window Station List and Station Map Symbols IndexIndex-2 Index-3 Index-4