Enterasys Networks B2G124-24 manual Regulatory Compliance Information

Page 4

REGULATORY COMPLIANCE INFORMATION

FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

INDUSTRY CANADA NOTICE

This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

CLASS A ITE NOTICE

WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CLASE A. AVISO DE ITE

ADVERTENCIA: Este es un producto de Clase A. En un ambiente doméstico este producto puede causar interferencia de radio en cuyo caso puede ser requerido tomar medidas adecuadas.

KLASSE A ITE ANMERKUNG

WARNHINWEIS: Dieses Produkt zählt zur Klasse A ( Industriebereich ). In Wohnbereichen kann es hierdurch zu Funkstörungen kommen, daher sollten angemessene Vorkehrungen zum Schutz getroffen werden.

PRODUCT SAFETY

This product complies with the following: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10.

SEGURIDAD DEL PRODUCTO

El producto de Enterasys cumple con lo siguiente: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10.

PRODUKTSICHERHEIT

Dieses Produkt entspricht den folgenden Richtlinien: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10.

ii

Image 4
Contents Enterasys SecureStack B2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv About This Guide Who Should Use This GuideRelated Documents How to Use This GuideFor Refer to Conventions Used in This Guide Following conventions are used in this guideConventions Used in This Guide Xviii About This Guide Introduction For information about Refer toOverview B2G124-24 and B2G124-48B2G124-24 Stackable Switch B2H124-48 Stackable Switch B2H124-48Connectivity Redundant Power Supply CapabilityHigh-Speed Stack Connections Description of Mini-GBICs Specification MGBIC-LC01Lanview Diagnostic LEDs Switch Configuration Using WebViewSwitch Configuration Using CLI Commands ManagementGetting Help Support@enterasys.comNetwork Requirements 10BASE-T Network1000BASE-FX Network 100BASE-TX Network1000BASE-T Network Hardware Installation Considerations Prior to Installation Unpacking the SwitchContents of Switch Carton Quantity Required ToolsInstalling Optional Mini-GBICs PreparationInstallation Removing the Mini-GBIC Installing the Switch on a Flat Surface Installing the Rubber FeetChassis Bottom, Rubber Feet Placement Guidelines for Flat Surface Installation Area Guidelines for Switch Installation on Flat SurfaceGuidelines for Rackmount Installation Rack Mounting the SwitchAttaching Brackets and Installing in Rack Connecting High-Speed Stacking Cables Attaching the Rackmount BracketsConnecting High-Speed Stacking Cables Configuring Switches in a Stack About SecureStack B2 Switch Operation in a StackConfiguring Switches in a Stack Recommended Procedures for New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesConnecting AC and RPS-SYS Power AC PowerSwitch Rear View C2RPS-SYS Redundant Power System Stack Initialization OverviewConnecting to Console Port for Local Management What Is NeededConnecting to an IBM or Compatible Device Parameter SettingConnecting to a VT Series Terminal 10 Connecting an IBM PC or CompatibleConnecting to a Modem 11 Connecting a VT Series TerminalConnecting to the Network Connecting UTP Cables13 Connecting a UTP Cable Segment to RJ45 Port 14 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ 1 RX1- 2 TX2+ 3 TX3+ 4 RX3- 5 RX2- 6 TX4+ 7 RX4 Connecting Fiber-Optic Cables to MT-RJ Ports B2G124-24 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 19 Cable Connection to LC Fiber-Optic Connectors Completing the Installation Initial Logon to Switch ManagementCompleting the Installation Hardware Installation Troubleshooting Using Lanview Lanview LEDs of B2G124-24 and B2G124-48 B2G124-24 shownLanview LEDs of B2H124-48 Lanview LEDs Color State Recommended ActionRPS Troubleshooting Checklist Refer to the SecureStack B2 Configuration Guide for properRefer to the SecureStack B2 Configuration Guide for Using the Reset Switch Reset SwitchSwitch Specifications SpecificationsTable A-1 Switch Specifications ItemSpecification B2G124-24 B2H124-48 Table A-1 Switch Specifications ItemSpecification B2G124-48Physical Table A-1 Switch Specifications EnvironmentalMini-GBIC Input/Output Specifications Gigabit Ethernet SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Table A-2 Mini-GBIC Input/Output Port SpecificationsMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELXTable A-9 MGBIC-08 Optical Specifications Table A-10 MGBIC-08 Operating Range 1550 nmTable A-11 MGBIC-02 Specifications MGBIC-02 Specifications 1000BASE-TConsole Port Pinout Assignments Regulatory Compliance Table A-12 Compliance Standards Regulatory ComplianceIndex NumericsPinout assignments console port A-7