Enterasys Networks B2G124-24 manual Enterasys NETWORKS, INC Firmware License Agreement

Page 9

ENTERASYS NETWORKS, INC.

FIRMWARE LICENSE AGREEMENT

BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,

CAREFULLY READ THIS LICENSE AGREEMENT.

This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc. on behalf of itself and its Affiliates (as hereinafter defined) (“Enterasys”) that sets forth Your rights and obligations with respect to the Enterasys software program/firmware installed on the Enterasys product (including any accompanying documentation, hardware or media) (“Program”) in the package and prevails over any additional, conflicting or inconsistent terms and conditions appearing on any purchase order or other document submitted by You. “Affiliate” means any person, partnership, corporation, limited liability company, or other form of enterprise that directly or indirectly through one or more intermediaries, controls, or is controlled by, or is under common control with the party specified. This Agreement constitutes the entire understanding between the parties, and supersedes all prior discussions, representations, understandings or agreements, whether oral or in writing, between the parties with respect to the subject matter of this Agreement. The Program may be contained in firmware, chips or other media.

BY INSTALLING OR OTHERWISE USING THE PROGRAM, YOU REPRESENT THAT YOU ARE AUTHORIZED TO ACCEPT THESE TERMS ON BEHALF OF THE END USER (IF THE END USER IS AN ENTITY ON WHOSE BEHALF YOU ARE AUTHORIZED TO ACT, “YOU” AND “YOUR” SHALL BE DEEMED TO REFER TO SUCH ENTITY) AND THAT YOU AGREE THAT YOU ARE BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES, AMONG OTHER PROVISIONS, THE LICENSE, THE DISCLAIMER OF WARRANTY AND THE LIMITATION OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT OR ARE NOT AUTHORIZED TO ENTER INTO THIS AGREEMENT, ENTERASYS IS UNWILLING TO LICENSE THE PROGRAM TO YOU AND YOU AGREE TO RETURN THE UNOPENED PRODUCT TO ENTERASYS OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.

IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT ENTERASYS NETWORKS, LEGAL DEPARTMENT AT (978) 684‐1000.

You and Enterasys agree as follows:

1.LICENSE. You have the non‐exclusive and non‐transferable right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions of this Agreement.

2.RESTRICTIONS. Except as otherwise authorized in writing by Enterasys, You may not, nor may You permit any third party to:

(i)Reverse engineer, decompile, disassemble or modify the Program, in whole or in part, including for reasons of error correction or interoperability, except to the extent expressly permitted by applicable law and to the extent the parties shall not be permitted by that applicable law, such rights are expressly excluded.

Information necessary to achieve interoperability or correct errors is available from Enterasys upon request and upon payment of Enterasys’ applicable fee.

(ii)Incorporate the Program, in whole or in part, in any other product or create derivative works based on the Program, in whole or in part.

(iii)Publish, disclose, copy, reproduce or transmit the Program, in whole or in part.

(iv)Assign, sell, license, sublicense, rent, lease, encumber by way of security interest, pledge or otherwise transfer the Program, in whole or in part.

(v)Remove any copyright, trademark, proprietary rights, disclaimer or warning notice included on or embedded in any part of the Program.

vii

Image 9
Contents Enterasys SecureStack B2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv Who Should Use This Guide About This GuideHow to Use This Guide Related DocumentsFor Refer to Following conventions are used in this guide Conventions Used in This GuideConventions Used in This Guide Xviii About This Guide For information about Refer to IntroductionB2G124-24 and B2G124-48 OverviewB2G124-24 Stackable Switch B2H124-48 B2H124-48 Stackable SwitchRedundant Power Supply Capability ConnectivityHigh-Speed Stack Connections MGBIC-LC01 Description of Mini-GBICs SpecificationSwitch Configuration Using WebView Lanview Diagnostic LEDsSwitch Configuration Using CLI Commands ManagementSupport@enterasys.com Getting Help10BASE-T Network Network Requirements100BASE-TX Network 1000BASE-FX Network1000BASE-T Network Hardware Installation Unpacking the Switch Considerations Prior to InstallationContents of Switch Carton Quantity Required ToolsPreparation Installing Optional Mini-GBICsInstallation Removing the Mini-GBIC Installing the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Area Guidelines for Switch Installation on Flat Surface Guidelines for Flat Surface InstallationRack Mounting the Switch Guidelines for Rackmount InstallationAttaching Brackets and Installing in Rack Attaching the Rackmount Brackets Connecting High-Speed Stacking CablesConnecting High-Speed Stacking Cables About SecureStack B2 Switch Operation in a Stack Configuring Switches in a StackConfiguring Switches in a Stack Installing a New Stackable System of Up to Eight Switches Recommended Procedures for New and Existing StacksAC Power Connecting AC and RPS-SYS PowerSwitch Rear View Stack Initialization Overview C2RPS-SYS Redundant Power SystemWhat Is Needed Connecting to Console Port for Local ManagementParameter Setting Connecting to an IBM or Compatible Device10 Connecting an IBM PC or Compatible Connecting to a VT Series Terminal11 Connecting a VT Series Terminal Connecting to a ModemConnecting UTP Cables Connecting to the Network13 Connecting a UTP Cable Segment to RJ45 Port 14 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ 1 RX1- 2 TX2+ 3 TX3+ 4 RX3- 5 RX2- 6 TX4+ 7 RX4 Connecting Fiber-Optic Cables to MT-RJ Ports B2G124-24 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 19 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationCompleting the Installation Hardware Installation Troubleshooting Lanview LEDs of B2G124-24 and B2G124-48 B2G124-24 shown Using LanviewLanview LEDs of B2H124-48 Color State Recommended Action Lanview LEDsRPS Refer to the SecureStack B2 Configuration Guide for proper Troubleshooting ChecklistRefer to the SecureStack B2 Configuration Guide for Reset Switch Using the Reset SwitchSpecifications Switch SpecificationsTable A-1 Switch Specifications ItemSpecification B2G124-24 Table A-1 Switch Specifications ItemSpecification B2G124-48 B2H124-48Physical Environmental Table A-1 Switch SpecificationsGigabit Ethernet Specifications Mini-GBIC Input/Output SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Table A-2 Mini-GBIC Input/Output Port SpecificationsMGBIC-LC03 Specifications 1000BASE-SX MGBIC-08 Specifications 1000BASE-ELX MGBIC-LC09 Specifications 1000BASE-LXTable A-9 MGBIC-08 Optical Specifications Table A-10 MGBIC-08 Operating Range 1550 nmMGBIC-02 Specifications 1000BASE-T Table A-11 MGBIC-02 SpecificationsConsole Port Pinout Assignments Table A-12 Compliance Standards Regulatory Compliance Regulatory ComplianceNumerics IndexPinout assignments console port A-7