Enterasys Networks B3G124-48P, B3G124-24P manual

Page 3

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

Notice

Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made.

The hardware, firmware, or software described in this document is subject to change without notice.

IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES.

Enterasys Networks, Inc.

50 Minuteman Road

Andover, MA 01810

2007 Enterasys Networks, Inc. All rights reserved. Part Number: 9034282‐02 February 2008

ENTERASYS, ENTERASYS NETWORKS, ENTERASYS MATRIX, ENTERASYS SECURESTACK, LANVIEW, NETSIGHT, WEBVIEW, and any logos associated therewith, are trademarks or registered trademarks of Enterasys Networks, Inc., in the United States and other countries.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

Documentation URL: http://www.enterasys.com/support/manuals

Documentacion URL: http://www.enterasys.com/support/manuals

Dokumentation im Internet: http://www.enterasys.com/support/manuals

i

Image 3
Contents Enterasys SecureStack B3 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv Who Should Use This Guide About This GuideHow to Use This Guide Related DocumentsFor Refer to Following conventions are used in this guide Conventions Used in This GuideGetting Help Overview IntroductionB3G124-24P Stackable Switch B3G124-24P Stackable Switch B3G124-48P Stackable SwitchHigh-Speed Stack Connections B3G124-48P Stackable SwitchPoE Power over Ethernet Support Redundant Power Supply CapabilityPowered Device Classifications PD Maximum Power Range Usage Connectivity Description of Mini-GBICs SpecificationStandards Compatibility Switch Configuration Using WebViewSwitch Configuration Using CLI Commands ManagementLanview Diagnostic LEDs Network Requirements 1000BASE-T Network 10BASE-TX Network100BASE-TX Network 1000BASE-FX NetworkHardware Installation Required Tools Considerations Prior to InstallationUnpacking the Switch Contents of Switch Carton QuantityPreparing to Install a Mini-GBIC Installing Optional Mini-GBICsMini-GBIC with MT-RJ Connector Installing a Mini-GBICRemoving a Mini-GBIC Mini-GBIC with LC ConnectorInstalling the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Area Guidelines for Switch Installation on Flat Surface Guidelines for Flat Surface InstallationRack Mounting the Switch Guidelines for Rackmount InstallationAttaching Brackets and Installing in Rack Attaching the Rackmount Brackets Connecting High-Speed Stacking Cables About SecureStack Switch Operation in a Stack Configuring Switches in a StackConfiguring Switches in a Stack Installing a New Stackable System of Up to Eight Switches Recommended Procedures to Install New and Existing StacksAC Power Connecting AC and PoE PowerConnecting AC Power and RPS Stack Manager Selection PoE Redundant Power SystemWhat Is Needed Connecting to Console Port for Local ManagementParameter Setting Connecting to an IBM or Compatible Device10 Connecting an IBM PC or Compatible Connecting to a VT Series Terminal11 Connecting a VT Series Terminal Connecting to a ModemConnecting UTP Cables Connecting to the Network13 Connecting a UTP Cable Segment to RJ45 Port 14 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to MT-RJ Ports Connecting to the Network Connecting Fiber-Optic Cables to LC Ports 19 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationUsing Lanview TroubleshootingCPU LED Stack Down LEDStack UP LED B3G124-48P Lanview LEDs Down Lanview LED Diagnostic IndicationsColor State Recommended Action CPURPS Mgbic Refer to the SecureStack B3 Configuration Guide for proper Troubleshooting ChecklistReset Switch Using the Reset SwitchUsing the Reset Switch Using the Reset Switch Troubleshooting Switch Specifications SpecificationsMtbf Table A-1 B3G124-24P and B3G124-48P SpecificationsTable A-2 Mini-GBIC Input/Output Port Specifications Mini-GBIC Input/Output SpecificationsGigabit Ethernet Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX Table A-11 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-9 MGBIC-08 Optical SpecificationsEMC Console Port Pinout AssignmentsRegulatory Compliance Table A-12 Compliance Standards Regulatory ComplianceRegulatory Compliance Specifications Numerics IndexMGBIC-LC01 A-4 MGBIC-LC03 A-4 MGBIC-LC09 A-5 MGBIC-MT01 A-4