Enterasys Networks B3G124-24P, B3G124-48P manual

Page 12

12.WAIVER. A waiver by Enterasys of a breach of any of the terms and conditions of this Agreement must be in writing and will not be construed as a waiver of any subsequent breach of such term or condition. Enterasys’ failure to enforce a term upon Your breach of such term shall not be construed as a waiver of Your breach or prevent enforcement on any other occasion.

13.SEVERABILITY. In the event any provision of this Agreement is found to be invalid, illegal or unenforceable, the validity, legality and enforceability of any of the remaining provisions shall not in any way be affected or impaired thereby, and that provision shall be reformed, construed and enforced to the maximum extent permissible. Any such invalidity, illegality or unenforceability in any jurisdiction shall not invalidate or render illegal or unenforceable such provision in any other jurisdiction.

14.TERMINATION. Enterasys may terminate this Agreement immediately upon Your breach of any of the terms and conditions of this Agreement. Upon any such termination, You shall immediately cease all use of the Program and shall return to Enterasys the Program and all copies of the Program.

x

Image 12
Contents Enterasys SecureStack B3 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv About This Guide Who Should Use This GuideHow to Use This Guide Related DocumentsFor Refer to Conventions Used in This Guide Following conventions are used in this guideGetting Help Introduction OverviewB3G124-24P Stackable Switch B3G124-48P Stackable Switch B3G124-24P Stackable SwitchB3G124-48P Stackable Switch High-Speed Stack ConnectionsPoE Power over Ethernet Support Redundant Power Supply CapabilityPowered Device Classifications PD Maximum Power Range Usage Description of Mini-GBICs Specification ConnectivitySwitch Configuration Using WebView Switch Configuration Using CLI CommandsManagement Standards CompatibilityLanview Diagnostic LEDs Network Requirements 10BASE-TX Network 100BASE-TX Network1000BASE-FX Network 1000BASE-T NetworkHardware Installation Considerations Prior to Installation Unpacking the SwitchContents of Switch Carton Quantity Required ToolsInstalling Optional Mini-GBICs Preparing to Install a Mini-GBICInstalling a Mini-GBIC Mini-GBIC with MT-RJ ConnectorMini-GBIC with LC Connector Removing a Mini-GBICInstalling the Switch on a Flat Surface Installing the Rubber FeetChassis Bottom, Rubber Feet Placement Guidelines for Flat Surface Installation Area Guidelines for Switch Installation on Flat SurfaceRack Mounting the Switch Guidelines for Rackmount InstallationAttaching Brackets and Installing in Rack Attaching the Rackmount Brackets Connecting High-Speed Stacking Cables Configuring Switches in a Stack About SecureStack Switch Operation in a StackConfiguring Switches in a Stack Recommended Procedures to Install New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesConnecting AC and PoE Power AC PowerConnecting AC Power and RPS PoE Redundant Power System Stack Manager SelectionConnecting to Console Port for Local Management What Is NeededConnecting to an IBM or Compatible Device Parameter SettingConnecting to a VT Series Terminal 10 Connecting an IBM PC or CompatibleConnecting to a Modem 11 Connecting a VT Series TerminalConnecting to the Network Connecting UTP Cables13 Connecting a UTP Cable Segment to RJ45 Port 14 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to MT-RJ Ports Connecting to the Network Connecting Fiber-Optic Cables to LC Ports 19 Cable Connection to LC Fiber-Optic Connectors Completing the Installation Initial Logon to Switch ManagementTroubleshooting Using LanviewCPU LED Stack Down LEDStack UP LED B3G124-48P Lanview LEDs Lanview LED Diagnostic Indications Color State Recommended ActionCPU DownRPS Mgbic Troubleshooting Checklist Refer to the SecureStack B3 Configuration Guide for properUsing the Reset Switch Reset SwitchUsing the Reset Switch Using the Reset Switch Troubleshooting Specifications Switch SpecificationsTable A-1 B3G124-24P and B3G124-48P Specifications MtbfMini-GBIC Input/Output Specifications Table A-2 Mini-GBIC Input/Output Port SpecificationsGigabit Ethernet Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-TTable A-9 MGBIC-08 Optical Specifications Table A-11 MGBIC-02 SpecificationsConsole Port Pinout Assignments Regulatory ComplianceTable A-12 Compliance Standards Regulatory Compliance EMCRegulatory Compliance Specifications Index NumericsMGBIC-LC01 A-4 MGBIC-LC03 A-4 MGBIC-LC09 A-5 MGBIC-MT01 A-4