Enterasys Networks 2G4072-52 Federal Communications Commission FCC Notice, Industry Canada Notice

Page 4

Regulatory Compliance Information

Federal Communications Commission (FCC) Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Industry Canada Notice

This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

Class A ITE Notice

WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Clase A. Aviso de ITE

ADVERTENCIA: Este es un producto de Clase A. En un ambiente doméstico este producto puede causar interferencia de radio en cuyo caso puede ser requerido tomar medidas adecuadas.

Klasse A ITE Anmerkung

WARNHINWEIS: Dieses Produkt zählt zur Klasse A ( Industriebereich ). In Wohnbereichen kann es hierdurch zu Funkstörungen kommen, daher sollten angemessene Vorkehrungen zum Schutz getroffen werden.

Product Safety

This product complies with the following: UL 60950, CSA C22.2 No. 60950, 2006/95/EC, EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10.

Seguridad del Producto

El producto de Enterasys cumple con lo siguiente: UL 60950, CSA C22.2 No. 60950, 2006/95/EC, EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10.

Produktsicherheit

Dieses Produkt entspricht den folgenden Richtlinien: UL 60950, CSA C22.2 No. 60950, 2006/95/EC, EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10.

ii

Image 4
Contents Enterasys Matrix Page Page Product Safety Federal Communications Commission FCC NoticeIndustry Canada Notice Class a ITE Notice Clase A. Aviso de ITEElectromagnetic Compatibility EMC Compatibilidad Electromágnetica EMCElektro- magnetische Kompatibilität EMC Hazardous SubstancesSupplement to Product Instructions Vcci Notice Bsmi EMC Statement TaiwanSafety Information Class 1 Laser Transceivers Declaration of ConformityEnterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix a Specifications TroubleshootingIndex Figures TablesXiv Who Should Use This Guide PrefaceImportant Notice Related Documents Structure of This GuideFor Refer to Document Conventions This guide uses the following conventionsGetting Help Support@enterasys.comIntroduction Switch Configuration Using WebView 2G4072-52Connectivity ManagementSwitch Configuration Using CLI Commands Lanview Diagnostic LEDsStandards Compatibility Lanview Diagnostic LEDs Introduction Network Requirements Link Aggregation10BASE-T Network 100BASE-TX Network1000BASE-SX/SX+/LX Network 1000BASE-T NetworkInstallation Unpacking the 2G4072-52Contents of 2G4072-52 Rack MountingAttaching Rack-mount Ears to Enterasys Matrix N SA 2G4072-52 Connecting Power Connecting PowerConnecting to the Network Connecting UTP CablesRX TX Crossover Four-Wire Cable RJ45 Pinouts Eight-Wire Crossover Cable RJ45 Pinouts Connecting Fiber-Optic Cables to Mini-GBICs 2G4072-52 2G4072-52 ÃÄÀ Connecting to the COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Parameter SettingConnecting to a VT Series Terminal 12 Connecting an IBM PC or CompatibleConnecting to a Modem 13 Connecting a VT Series Terminal14 Connecting to a Modem COM Port Adapter Wiring and Signal Diagram RJ45 Adapter Wiring and Signal AssignmentsVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Log-In Using a Console Port Connection Completing the InstallationModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation 15 Matrix Startup Screen Example N7 Chassis Using Lanview TroubleshootingViewing the Receive and Transmit Activity LED Color State Recommended ActionAlternating 67% on, 33% off Troubleshooting Checklist Refer to the Enterasys Matrix N Standalone SeriesTroubleshooting Checklist Overview of Shutdown ProcedureProblem Possible Cause Recommended Action Recommended Shutdown Procedure Using Reset Button Last Resort Shutdown Procedure Using Reset ButtonSpecifications 2G4072-52 SpecificationsTable A-1 Specifications ItemSpecification 2G4072-52 PortsMini-GBIC Input/Output Specifications Table A-2 Mini-GBIC Input/Output Port SpecificationsProcessors/Memory PhysicalMGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SX Gigabit Ethernet SpecificationsMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-TTable A-7 MGBIC-08 Optical Specifications Table A-9 MGBIC-02 SpecificationsTable A-3 COM Port Pin Assignments Signal Name Input/Output COM Port Pinout AssignmentsRegulatory Compliance Table A-4 Compliance Standards Regulatory ComplianceMode Switch Bank Settings and Optional Installations Setting the Mode Switches Required ToolsFigure B-1 Mode Switch Location Memory Locations and Replacement Procedures Location of Dimm and Dram Simm Memory ModulesDimm Replacement Procedure Removing the DimmInstalling the Dimm Figure B-4 Installing the DimmRemoving the Dram Simm Figure B-5 Removing Chassis CoverInstalling the Dram Simm Figure B-6 Dram Simm Connector LocationFigure B-7 Installing the Dram Simm Page Index NumericsPinout assignments console port A-6