Enterasys Networks 2G4072-52 manual Mode Switch Bank Settings and Optional Installations

Page 59

B

Mode Switch Bank Settings and Optional Installations

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Eléctrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

This appendix covers the following items:

For information about...	Refer to page...

Required Tools	B-2

Setting the Mode Switches	B-2

Memory Locations and Replacement Procedures	B-2

Electrical Hazard: Do not remove the cover from the 2G4072-52 while power is applied to the unit. Hazardous voltages are present and could cause personal injury and/or damage the unit.

Do not power up the 2G4072-52 again until the cover and screws are in place.

Riesgo Eléctrico: No debe de remover la tapa durente que este coneltado a la corriente, una descarga electrica le puede causar y probocarle daños, al igual que al aparato.

No enchufe a la corriente hasta que la tapa y los tornillos esten en su lugar.

Elektrischer Gefahrenhinweis: Entfernen sie nicht den Deckel des C, wenn dieser noch an die Stromzufuhr angeschossen ist, gefährliche Spannungen können Personen verletzten oder das Gerät beschädigen.

Schalten Sie den 2G4072-52 nicht ein, bevor der Deckel das Gerät abdeckt und mit den Schrauben fixiert wurde.

N Standalone Series Installation Guide B-1

Image 59

Contents Enterasys Matrix Page Page Class a ITE Notice Clase A. Aviso de ITE Product SafetyFederal Communications Commission FCC Notice Industry Canada NoticeHazardous Substances Electromagnetic Compatibility EMCCompatibilidad Electromágnetica EMC Elektro- magnetische Kompatibilität EMCSupplement to Product Instructions Bsmi EMC Statement Taiwan Vcci NoticeDeclaration of Conformity Safety Information Class 1 Laser TransceiversEnterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Index TroubleshootingAppendix a Specifications Tables FiguresXiv Important Notice PrefaceWho Should Use This Guide For Refer to Structure of This GuideRelated Documents This guide uses the following conventions Document ConventionsSupport@enterasys.com Getting HelpIntroduction Management Switch Configuration Using WebView2G4072-52 ConnectivityStandards Compatibility Lanview Diagnostic LEDsSwitch Configuration Using CLI Commands Lanview Diagnostic LEDs Introduction Link Aggregation Network Requirements1000BASE-T Network 10BASE-T Network100BASE-TX Network 1000BASE-SX/SX+/LX NetworkUnpacking the 2G4072-52 InstallationRack Mounting Contents of 2G4072-52Attaching Rack-mount Ears to Enterasys Matrix N SA 2G4072-52 Connecting Power Connecting PowerConnecting UTP Cables Connecting to the NetworkRX TX Crossover Four-Wire Cable RJ45 Pinouts Eight-Wire Crossover Cable RJ45 Pinouts Connecting Fiber-Optic Cables to Mini-GBICs 2G4072-52 2G4072-52 ÃÄÀ Parameter Setting Connecting to the COM Port for Local ManagementWhat Is Needed Connecting to an IBM PC or Compatible Device12 Connecting an IBM PC or Compatible Connecting to a VT Series Terminal13 Connecting a VT Series Terminal Connecting to a Modem14 Connecting to a Modem VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Adapter Wiring and Signal AssignmentsCOM Port Adapter Wiring and Signal Diagram RJ45 Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the InstallationLog-In Using a Console Port Connection Completing the Installation 15 Matrix Startup Screen Example N7 Chassis Viewing the Receive and Transmit Activity TroubleshootingUsing Lanview Color State Recommended Action LEDAlternating 67% on, 33% off Refer to the Enterasys Matrix N Standalone Series Troubleshooting ChecklistProblem Possible Cause Recommended Action Overview of Shutdown ProcedureTroubleshooting Checklist Last Resort Shutdown Procedure Using Reset Button Recommended Shutdown Procedure Using Reset Button2G4072-52 Ports Specifications2G4072-52 Specifications Table A-1 Specifications ItemSpecificationPhysical Mini-GBIC Input/Output SpecificationsTable A-2 Mini-GBIC Input/Output Port Specifications Processors/MemoryMGBIC-LC03 Specifications 1000BASE-SX Gigabit Ethernet SpecificationsMGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX Table A-9 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-7 MGBIC-08 Optical SpecificationsTable A-4 Compliance Standards Regulatory Compliance Table A-3 COM Port Pin Assignments Signal Name Input/OutputCOM Port Pinout Assignments Regulatory ComplianceMode Switch Bank Settings and Optional Installations Required Tools Setting the Mode SwitchesFigure B-1 Mode Switch Location Location of Dimm and Dram Simm Memory Modules Memory Locations and Replacement ProceduresRemoving the Dimm Dimm Replacement ProcedureFigure B-4 Installing the Dimm Installing the DimmFigure B-5 Removing Chassis Cover Removing the Dram SimmFigure B-6 Dram Simm Connector Location Installing the Dram SimmFigure B-7 Installing the Dram Simm Page Numerics IndexPinout assignments console port A-6