Enterasys Networks 2G4072-52 manual

Page 3

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

Notice

Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made.

The hardware, firmware, or software described in this document is subject to change without notice.

IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES.

Enterasys Networks, Inc.

50 Minuteman Road

Andover, MA 01810

♥2008 Enterasys Networks, Inc. All rights reserved. Part Number: 9033973‐04 July 2008

ENTERASYS NETWORKS, ENTERASYS MATRIX, LANVIEW, MATRIX, ENTERASYS NETSIGHT, WEBVIEW, and any logos associated therewith, are trademarks or registered trademarks of Enterasys Networks, Inc., in the United States and other countries. For a complete list of Enterasys trademarks, see http://www.enterasys.com/company/trademarks.aspx.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

Documentation URL: http://www.enterasys.com/support/manuals

Documentacion URL: http://www.enterasys.com/support/manuals

Dokumentation im Internet: http://www.enterasys.com/support/manuals

i

Image 3

Contents Enterasys Matrix Page Page Class a ITE Notice Clase A. Aviso de ITE Product SafetyFederal Communications Commission FCC Notice Industry Canada NoticeHazardous Substances Electromagnetic Compatibility EMCCompatibilidad Electromágnetica EMC Elektro- magnetische Kompatibilität EMCSupplement to Product Instructions Bsmi EMC Statement Taiwan Vcci NoticeDeclaration of Conformity Safety Information Class 1 Laser TransceiversEnterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Troubleshooting Appendix a SpecificationsIndex Tables FiguresXiv Preface Who Should Use This GuideImportant Notice Structure of This Guide Related DocumentsFor Refer to This guide uses the following conventions Document ConventionsSupport@enterasys.com Getting HelpIntroduction Management Switch Configuration Using WebView2G4072-52 ConnectivityLanview Diagnostic LEDs Switch Configuration Using CLI CommandsStandards Compatibility Lanview Diagnostic LEDs Introduction Link Aggregation Network Requirements1000BASE-T Network 10BASE-T Network100BASE-TX Network 1000BASE-SX/SX+/LX NetworkUnpacking the 2G4072-52 InstallationRack Mounting Contents of 2G4072-52Attaching Rack-mount Ears to Enterasys Matrix N SA 2G4072-52 Connecting Power Connecting PowerConnecting UTP Cables Connecting to the NetworkRX TX Crossover Four-Wire Cable RJ45 Pinouts Eight-Wire Crossover Cable RJ45 Pinouts Connecting Fiber-Optic Cables to Mini-GBICs 2G4072-52 2G4072-52 ÃÄÀ Parameter Setting Connecting to the COM Port for Local ManagementWhat Is Needed Connecting to an IBM PC or Compatible Device12 Connecting an IBM PC or Compatible Connecting to a VT Series Terminal13 Connecting a VT Series Terminal Connecting to a Modem14 Connecting to a Modem Adapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation Log-In Using a Console Port ConnectionModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation 15 Matrix Startup Screen Example N7 Chassis Troubleshooting Using LanviewViewing the Receive and Transmit Activity Color State Recommended Action LEDAlternating 67% on, 33% off Refer to the Enterasys Matrix N Standalone Series Troubleshooting ChecklistOverview of Shutdown Procedure Troubleshooting ChecklistProblem Possible Cause Recommended Action Last Resort Shutdown Procedure Using Reset Button Recommended Shutdown Procedure Using Reset Button2G4072-52 Ports Specifications2G4072-52 Specifications Table A-1 Specifications ItemSpecificationPhysical Mini-GBIC Input/Output SpecificationsTable A-2 Mini-GBIC Input/Output Port Specifications Processors/MemoryGigabit Ethernet Specifications MGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX Table A-9 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-7 MGBIC-08 Optical SpecificationsTable A-4 Compliance Standards Regulatory Compliance Table A-3 COM Port Pin Assignments Signal Name Input/OutputCOM Port Pinout Assignments Regulatory ComplianceMode Switch Bank Settings and Optional Installations Required Tools Setting the Mode SwitchesFigure B-1 Mode Switch Location Location of Dimm and Dram Simm Memory Modules Memory Locations and Replacement ProceduresRemoving the Dimm Dimm Replacement ProcedureFigure B-4 Installing the Dimm Installing the DimmFigure B-5 Removing Chassis Cover Removing the Dram SimmFigure B-6 Dram Simm Connector Location Installing the Dram SimmFigure B-7 Installing the Dram Simm Page Numerics IndexPinout assignments console port A-6