Enterasys Networks manual Installation, Unpacking the 2G4072-52

Page 27

3

Installation

This chapter provides the instructions to install the 2G4072‐52.

A Phillips screwdriver is required only to attach two optional rack‐mounting brackets on the 2G4072‐52. Follow the order of the sections listed below for correct installation:

For information about...	Refer to page...

Unpacking the 2G4072-52	3-1

Rack Mounting	3-2

Connecting Power	3-4

Connecting to the Network	3-5

Connecting to the COM Port for Local Management	3-13

Completing the Installation	3-18

Important Notice

Read the Release Notes shipped with the 2G4072-52 to check for any exceptions to the supported features and operation documented in this guide.

Unpacking the 2G4072-52

Unpack the 2G4072‐52 as follows:

1.Open the box and remove the packing material protecting the Enterasys Matrix N SA 2G4072‐52.

2.Open the accessory kit and remove the power cord, rack‐mount ears, screws, DB9 to RJ45 converter, and adhesive feet (for desk‐top placement).

3.Verify the contents of the carton as listed in the table below.

N Standalone Series Installation Guide 3-1

Image 27

Contents Enterasys Matrix Page Page Class a ITE Notice Clase A. Aviso de ITE Product SafetyFederal Communications Commission FCC Notice Industry Canada NoticeHazardous Substances Electromagnetic Compatibility EMCCompatibilidad Electromágnetica EMC Elektro- magnetische Kompatibilität EMCSupplement to Product Instructions Bsmi EMC Statement Taiwan Vcci NoticeDeclaration of Conformity Safety Information Class 1 Laser TransceiversEnterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Troubleshooting Appendix a SpecificationsIndex Tables FiguresXiv Preface Who Should Use This GuideImportant Notice Structure of This Guide Related DocumentsFor Refer to This guide uses the following conventions Document ConventionsSupport@enterasys.com Getting HelpIntroduction Management Switch Configuration Using WebView2G4072-52 ConnectivityLanview Diagnostic LEDs Switch Configuration Using CLI CommandsStandards Compatibility Lanview Diagnostic LEDs Introduction Link Aggregation Network Requirements1000BASE-T Network 10BASE-T Network100BASE-TX Network 1000BASE-SX/SX+/LX NetworkUnpacking the 2G4072-52 InstallationRack Mounting Contents of 2G4072-52Attaching Rack-mount Ears to Enterasys Matrix N SA 2G4072-52 Connecting Power Connecting PowerConnecting UTP Cables Connecting to the NetworkRX TX Crossover Four-Wire Cable RJ45 Pinouts Eight-Wire Crossover Cable RJ45 Pinouts Connecting Fiber-Optic Cables to Mini-GBICs 2G4072-52 2G4072-52 ÃÄÀ Parameter Setting Connecting to the COM Port for Local ManagementWhat Is Needed Connecting to an IBM PC or Compatible Device12 Connecting an IBM PC or Compatible Connecting to a VT Series Terminal13 Connecting a VT Series Terminal Connecting to a Modem14 Connecting to a Modem Adapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation Log-In Using a Console Port ConnectionModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation 15 Matrix Startup Screen Example N7 Chassis Troubleshooting Using LanviewViewing the Receive and Transmit Activity Color State Recommended Action LEDAlternating 67% on, 33% off Refer to the Enterasys Matrix N Standalone Series Troubleshooting ChecklistOverview of Shutdown Procedure Troubleshooting ChecklistProblem Possible Cause Recommended Action Last Resort Shutdown Procedure Using Reset Button Recommended Shutdown Procedure Using Reset Button2G4072-52 Ports Specifications2G4072-52 Specifications Table A-1 Specifications ItemSpecificationPhysical Mini-GBIC Input/Output SpecificationsTable A-2 Mini-GBIC Input/Output Port Specifications Processors/MemoryGigabit Ethernet Specifications MGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX Table A-9 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-7 MGBIC-08 Optical SpecificationsTable A-4 Compliance Standards Regulatory Compliance Table A-3 COM Port Pin Assignments Signal Name Input/OutputCOM Port Pinout Assignments Regulatory ComplianceMode Switch Bank Settings and Optional Installations Required Tools Setting the Mode SwitchesFigure B-1 Mode Switch Location Location of Dimm and Dram Simm Memory Modules Memory Locations and Replacement ProceduresRemoving the Dimm Dimm Replacement ProcedureFigure B-4 Installing the Dimm Installing the DimmFigure B-5 Removing Chassis Cover Removing the Dram SimmFigure B-6 Dram Simm Connector Location Installing the Dram SimmFigure B-7 Installing the Dram Simm Page Numerics IndexPinout assignments console port A-6