Enterasys Networks 2G4072-52 manual

Page 36

Connecting to the Network

2.Insert the MT‐RJ cable connector into the Mini‐GBIC until it clicks into place.

Note: To remove the MT-RJ cable connector, press on its release tab and pull it out of the Mini-GBIC.

Figure 3-9 Cable Connection to MT-RJ Fiber-Optic Connectors

Á

Å

À

Ä

13 14

16

17

Â

Ã

18 19 20

2G4072-52

1	Mini-GBIC (MGBIC-MT01)	4	Port slot
2	Mini-GBIC,top side	5	Mini-GBIC,protective dust cover
3	7-Pin edge connector (insertion side)	6	Release tab

3-10 Installation

Image 36

Contents Enterasys Matrix Page Page Product Safety Federal Communications Commission FCC NoticeIndustry Canada Notice Class a ITE Notice Clase A. Aviso de ITEElectromagnetic Compatibility EMC Compatibilidad Electromágnetica EMCElektro- magnetische Kompatibilität EMC Hazardous SubstancesSupplement to Product Instructions Vcci Notice Bsmi EMC Statement TaiwanSafety Information Class 1 Laser Transceivers Declaration of ConformityEnterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Troubleshooting Appendix a SpecificationsIndex Figures TablesXiv Preface Who Should Use This GuideImportant Notice Structure of This Guide Related DocumentsFor Refer to Document Conventions This guide uses the following conventionsGetting Help Support@enterasys.comIntroduction Switch Configuration Using WebView 2G4072-52Connectivity ManagementLanview Diagnostic LEDs Switch Configuration Using CLI CommandsStandards Compatibility Lanview Diagnostic LEDs Introduction Network Requirements Link Aggregation10BASE-T Network 100BASE-TX Network1000BASE-SX/SX+/LX Network 1000BASE-T NetworkInstallation Unpacking the 2G4072-52Contents of 2G4072-52 Rack MountingAttaching Rack-mount Ears to Enterasys Matrix N SA 2G4072-52 Connecting Power Connecting PowerConnecting to the Network Connecting UTP CablesRX TX Crossover Four-Wire Cable RJ45 Pinouts Eight-Wire Crossover Cable RJ45 Pinouts Connecting Fiber-Optic Cables to Mini-GBICs 2G4072-52 2G4072-52 ÃÄÀ Connecting to the COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Parameter SettingConnecting to a VT Series Terminal 12 Connecting an IBM PC or CompatibleConnecting to a Modem 13 Connecting a VT Series Terminal14 Connecting to a Modem Adapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation Log-In Using a Console Port ConnectionModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation 15 Matrix Startup Screen Example N7 Chassis Troubleshooting Using LanviewViewing the Receive and Transmit Activity LED Color State Recommended ActionAlternating 67% on, 33% off Troubleshooting Checklist Refer to the Enterasys Matrix N Standalone SeriesOverview of Shutdown Procedure Troubleshooting ChecklistProblem Possible Cause Recommended Action Recommended Shutdown Procedure Using Reset Button Last Resort Shutdown Procedure Using Reset ButtonSpecifications 2G4072-52 SpecificationsTable A-1 Specifications ItemSpecification 2G4072-52 PortsMini-GBIC Input/Output Specifications Table A-2 Mini-GBIC Input/Output Port SpecificationsProcessors/Memory PhysicalGigabit Ethernet Specifications MGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-TTable A-7 MGBIC-08 Optical Specifications Table A-9 MGBIC-02 SpecificationsTable A-3 COM Port Pin Assignments Signal Name Input/Output COM Port Pinout AssignmentsRegulatory Compliance Table A-4 Compliance Standards Regulatory ComplianceMode Switch Bank Settings and Optional Installations Setting the Mode Switches Required ToolsFigure B-1 Mode Switch Location Memory Locations and Replacement Procedures Location of Dimm and Dram Simm Memory ModulesDimm Replacement Procedure Removing the DimmInstalling the Dimm Figure B-4 Installing the DimmRemoving the Dram Simm Figure B-5 Removing Chassis CoverInstalling the Dram Simm Figure B-6 Dram Simm Connector LocationFigure B-7 Installing the Dram Simm Page Index NumericsPinout assignments console port A-6