Dish Network HOME NETWORK manual Page, Description, Procedure, HomePlug

Page 17

Description

 

Procedure

 

 

 

HomePlug

1.

Ensure the HomePlug-to-Ethernet adapter is plugged firmly into the electrical outlet. The

Troubleshooting

 

adapter should not be plugged into a GFI electrical outlet.

 

2.

Verify the HomePlug-to-Ethernet adapter is not plugged into a switched outlet.

 

3.

If a surge protector is used for either the satellite receiver or the HomePlug-to-Ethernet

 

 

adapter, a surge protector that is approved for use with HomePlug devices must be used,

 

 

and the adapter and receiver must be plugged into the HomePlug outlet.

 

4.

Dimmers for home lighting can interfere with HomePlug. It is not recommended to use

 

 

dimmers on the same circuit as HomePlug equipment.

 

5.

Verify the Ethernet cable is “clicked in” on the adapter’s ETHERNET port and the ETHERNET

 

 

port on the router.

 

6.

Try connecting the Ethernet cable to a different ETHERNET port on the router/switch.

 

 

A program that I

- If you began viewing the program, the rental period may have expired.

downloaded

- Programs that are downloaded but not viewed will remain on the My Rentals list for a

disappeared from

 

limited time period. After that time period, the program automatically expires and is

the My Rentals list

 

deleted from the My Rentals list.

 

- Someone else in the household may have deleted the program from the My Rentals list.

 

 

 

I am unable to

1.

The satellite receiver must have satellite signal to begin a new download. If you have

start downloading

 

received an error message such as “Acquiring Satellite Signal” or “Satellite Signal has

a program

 

been lost”, your signal loss issue needs to be resolved before you can download programs.

 

 

Refer to tech.dishnetwork.com for signal loss troubleshooting steps.

 

2.

If your receiver has satellite signal but you are still unable to download movies, refer to

 

 

the troubleshooting steps Connection status on Network Setup screen is Not Connected, or

 

 

Error 789 is received when DISH Theater or New Releases is selected on page 14.

 

 

The DISH

The DISH Network server providing the content may be experiencing a temporary

Theater, New

interruption. Wait approximately 30 minutes, then try accessing these options to see if

Releases, or After

content is listed.

Hours options

 

 

have no content

 

 

listed

 

 

 

 

 

Page 16

Image 17
Contents Installation Instructions Home NetworkTable of Contents Installation InstructionsInstallation Considerations Quick Installation InstructionsOverview Quick Installation InstructionsIdentifying the Home Network and Receiver Connection Method Identifying and Creating the Home Network and Available Ethernet PortFigure 4. Identifying Ethernet Switch or Hub No. Go to Adding an Ethernet Switch on pageFigure 5. Identifying Available Ethernet Port on Switch or Hub Figure 3. Identifying Available Ethernet PortAdding an Ethernet Switch Installation and SetupDiagram 1. Overview of Home Network with Ethernet Switch Connected Diagram 2. Connecting an Ethernet Switch to the RouterINTERNET, or WAN Diagram 4. Connecting the Receiver to the Router Using Ethernet Cable Connecting the Satellite Receiver to an Available Ethernet PortEthernet Port Ethernet Port One HomePlug-to-Ethernet adapter must be obtained for use at the location of the router, gateway, or Ethernet switch. One adapter supports up to 15 receivers. The ViP-series of DISH Network receivers include HomePlug 1.0 support. HomePlug Turbo adapters can also be used Select Done to exit the Network Setup screen Diagnostics Screen Using DishONLINE New Releases and DISH Theater Procedure TroubleshootingHomePlug Troubleshooting section on page DescriptionNetwork Setup. Select Reset Connection address on the receiver’s Network Setup screen shows all 0s on pageHomePlug 156342