Dell 6248P, 6224P, 6224F specifications ¾ auto-cost reference bandwidth and bandwidth Commands

Page 10

¾Granular OSPF v2/v3 Traps

Configure which of the OSPF traps the OSPF Router should generate by enabling or disabling the trap condition. If a trap condition is enabled and the condition is detected, the OSPF router will send the trap to all trap receivers.

¾auto-cost reference bandwidth and bandwidth Commands

Controls how OSPF calculates the default metric for an interface by using the auto-cost command in router OSPF configuration mode. To assign cost-based only on the interface type, use the no form of this command.

¾network area Command

Support is added for the following 2 OSPFv2 CLI commands:

network ip-address wildcard-mask area areaid

ip ospf area areaid [ secondaries none ]

¾OSPF v2/v3 Route Preferences Rework

The following effects are seen with this change:

Configuration of external route preference that applies to all OSPF external routes (like type1, type2, nssa-type1, nssa-type2) equally.

Allows multiple route types to be configured with equal preference values.

No longer follows the order among OSPF route preferences: intra < inter < external.

Configuring the route preference of 255 makes the route ineligible to be selected as the best route to its destination (a route with preference of 255 is never used for forwarding).

While migrating from previous releases, the preference for the external routes will be set with the preference value of the type-1 route in the earlier releases.

¾Opaque LSAs and Detailed Display of OSPF v2 LSAs

Opaque LSAs provide a generalized mechanism to allow for the future extensibility of OSPF. The information contained in Opaque LSAs may be used directly by OSPF or indirectly by some application wishing to distribute information throughout the OSPF domain. For example, the OSPF LSA may be used by routers to distribute IP to link-layer address resolution information.

¾ICMP Enhancements (RFC4443)

ICMPv6 code is updated to support RFC 4443.

¾DNSv6 Client

The DNS Client has added support for IPv6 (RFC3596). The transport for communication with a DNS server can be either IPv6 or IPv4 depending on type of server address.

8

System Firmware Version 3.2.0.6

Image 10
Contents PowerConnect 6224/6224F/6224P/6248/6248P Release Notes Table of Contents Firmware Upgrade Firmware Specifications Firmware Version DetailsGlobal Support Firmware Downgrade Hardware SupportedSupported Firmware Functionality Version No Release DateAdded Functionality in this Release System Firmware Version PowerConnect 6224/6224F/6224P/6248/6248P Release Notes System Firmware Version PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ auto-cost reference bandwidth and bandwidth Commands PowerConnect 6224/6224F/6224P/6248/6248P Release Notes System Firmware Version Changed Functionality in this Release ¾ bridge address Command Changed PowerConnect 6224/6224F/6224P/6248/6248P Release Notes Maximum rules per ACL are Deprecated Commands and Parameters Title Description Ip ospf Ip ospf areaidNo switch 2 priority 2 command Issues ResolvedDescription User Impact Resolution Snmp-server host ipaddress and soWeb page EAP Statistics Before processing System Firmware Version Nsf ietf helper strict-lsa-checking Non-Stop ForwardingTitle Description No nsf ietf helper strict-lsa-checkingCustom Protocol Based VLANs Port Configuration Show CommandVlan Name Support with Radius Server Radius Accounting Servers Stacking/CX-4 Module ConfigurationConfigurable Message of the Day Banner Spanning TreeConfiguring Dell PowerConnect Title Description User’s Guide UpdatesLink Dependency Commands MulticastKnown Issues Summary User Impact WorkaroundShow running PowerConnect 6224/6224F/6224P/6248/6248P Release Notes QoS Known Restrictions and Limitations Layer802.1AB Lldp 802.1XInterfaces. ip default gateway is for Description User Impact Vlan association mac commandDescription User Impact Ip default gateway and ip default IP MapIcmp MulticastManagement Web-based ManagementCable Diagnostics File Management