Furuno RD-30 Heading Sensor PG-1000, C-2000 Setup, Calibration, HDG Sensor Setup, HDG Setup menu

Page 36

1. OPERATION

1.17Heading Sensor PG-1000, C-2000 Setup

Set up the heading sensor PG1000, C-2000 on the HDG SETUP menu, with the heading sensor connected to the AUX port. Note that no data is transmitted from the IN/OUT port when the HDG SETUP menu is displayed.

Calibration

Calibrate the heading sensor against magnetic field distortion aboard the boat as below. Do not turn off the power during the calibration.

1.Find a calm and clear area without current, wind, swell or waves.

2.Steer the boat clockwise or counterclockwise in a circular course. Take about two minutes to complete the circle (at about 3 kt). While turning the boat, go to step 3.

2 minutes for a circle (at about 3 kt)

Course to follow for calibration

Notes: Speed higher than 3 kt may result in calibration error.

3.Press the [MENU] key once or twice to open the menu.

4.Choose HDG SETUP and then press the [MENU] key. (It may take several seconds before the HDG SETUP menu appears.)

HDG SENSOR SETUP

CALIBRATION

OFFSET : -14 352￿M

DAMPING : 1*

Offset output from PG-1000 or C-2000 and current bearing (updated every second)

Damping factor set at C-2000

* = DAMPING shown on C-2000.

HDG SETUP menu

5. Choose CALIBRATION and then press the [ENT] key.

1-30

Image 36
Contents Multi Display 00080917705 Safety Instructions Table of Contents Features ForewordWord to the Owner of the RD-30 Multi Display IiiFuruno Operation ControlsRD-30 Turning On/Off the Power 210.2 Sample displays Graph displaysGraphic displays Graphic displaysHighway display Highway displayZoom window Setting up the Displays User display setup menuChoosing display type Main menuSetting up digital displays Setting up graph displays Digital display optionsGraph display setup menus Graph display options windowGraph setup menus Start From +Setting up graphic displays Speedometer and water temperature graphic menusGraphic display options window Displaying Rx Data Rx data displayAlarms Audio alarm typeALARM1 menu Buzzer options windowSpeed alarm LOW High Insde Outsd ShearDepth alarm Arrival alarm, anchor watch alarm XTE Cross Track Error alarm Trip alarmHow the XTE alarm works Odometer alarm Time alarmCountdown alarm Alarm messages MessagesMessages display Resetting Indications to Zero ResetReset menu Windows for resetting trip, odometer and graph displaysUnits setup menu Choosing Units of MeasurementKM, KM/H Unit optionsApplying an Offset to Data OffsetsOffsets menu System Setup menu Choosing Time Display Format12HOUR Time display optionsTD setup options Choosing Position Data FormatPosition format options Simulation Mode 14 I/O Port SetupPorts Setup menu IN/OUT, AUX and Power OUT optionsIN/PUT and AUX Both Setup menu Bearing ReferenceTrue BRG Read optionsMagnetic Variation ManualMAG VAR. options Heading Sensor PG-1000, C-2000 Setup HDG Sensor SetupHDG Setup menu CalibrationCalibration Calibration promptCalibration results Offset Damping C-2000Damping options MAINTENANCE, Troubleshooting Diagnostic Test Test Start screenTest display When Battery ALARM! Appears Exchange battery windowLCD Check screen Clearing Backup Data ALARM1 Menu TreeSYS Setup Loran C/ a Chains GRIDecca Chains Chain Location CodeFuruno Specifications of MULTI-DISPLAY RD-30This page is intentionally left blank Index Index-1

RD-30 specifications

The Furuno RD-30 is a multifunctional marine display unit designed for navigating and managing various marine data effectively. As a robust and reliable product from a reputable manufacturer known for its innovative nautical technologies, the RD-30 is a favored choice among sailors and boaters around the world.

One of the main features of the RD-30 is its ability to integrate with multiple Furuno systems, allowing for seamless data sharing and control. The device can display information from GPS, radar, and other instruments, providing a comprehensive view of the vessel’s navigation status. This integration not only simplifies the navigation process but also enhances safety by combining critical data points into a single display.

The RD-30 is equipped with a user-friendly interface that facilitates easy operation. Its clear and bright LCD display delivers excellent visibility in various lighting conditions. The large font sizes and intuitive menu structure make it easy for users to access essential information quickly, ensuring that they can focus on navigation without distractions.

Another significant characteristic of the RD-30 is its versatility. It features various display modes, allowing users to customize how they view their navigation data. Whether it’s speed, distance traveled, or water depth, the RD-30 can present information in a format that best suits the user’s needs. Additionally, the unit supports multiple languages, catering to a diverse user base.

Technologically, the RD-30 embodies Furuno's commitment to innovation. It utilizes advanced sensor technology, leveraging data from external instruments to provide real-time updates. The device can also interface with NMEA 0183 and NMEA 2000 networks, which broadens integration possibilities with other onboard electronics.

Moreover, the RD-30 features a lightweight design which makes it easy to mount on various vessels, from small recreational boats to larger yachts. Its compact form factor does not compromise functionality, as it remains packed with essential features for avid sailors.

In conclusion, the Furuno RD-30 stands out for its multifunctionality, ease of use, and robust integration capabilities. Designed for both amateur and experienced mariners, the RD-30 enhances navigational safety and efficiency, making it an indispensable tool in modern marine travel. As technology continues to evolve, the RD-30 remains a testament to Furuno's dedication to quality and innovation in the maritime industry.