Carrier Access 770-0125-AB installation manual

Page 2

Copyright© 2004 Carrier Access Corporation. All rights reserved.

The information presented in this manual is subject to change without notice and does not represent a commitment on the part of Carrier Access Corporation. The hardware and software described herein are furnished under a license or non- disclosure agreement. The hardware, software, and manual may be used or copied only in accordance with the terms of this agreement. It is against the law to reproduce, transmit, transcribe, store in a retrieval system, or translate into any medium

-electronic, mechanical, magnetic, optical, chemical, manual, or otherwise - any part of this manual or software supplied with BROADway for any purpose other than the purchaser’s personal use without the express written permission of Carrier Access Corporation.

BROADway, solve for x, and the Carrier Access Logo are registered trademarks of Carrier Access Corporation. All other brand or product names are trademarks or registration trademarks of their respective companies or organizations.

Contact Information:

Carrier Access Corporation 5395 Pearl Parkway Boulder, CO 80301-2490 Corporate Phone: (800) 495-5455 Fax: (303) 443-5908 www.carrieraccess.com

Customer Support Direct: (800) 786-9929

E-mail: tech-support@carrieraccess.com

Image 2

Contents BROADway Page FCC Requirements, Part Safety of Information Technology EquipmentCompliance Type Card Service Framing CodingNetwork JackEnglish Industry Canada ICES-003Industry Canada CS-03 FrenchSafety Information Electrostatic Discharge ESD Precautions Warranty Product Returns WarrantyLimitation of Warranty & Limitation of Remedies Third-Party Software Notices Sun Microsystems, Inc., Software NoticePreface Table of Contents Configuration Table of ContentsPorts and Cables IndexXiv BROADway Release Chapter Overview Installation Chassis Overview Top I/O Panel Front View of the Bits ChassisTop I/O Panel Front View of the ITU Chassis Mounting the Chassis in a Rack Mounting the Chassis in a RackSide View of the Chassis Cabling Power and Ground Extension PlateBROADway Chassis Rear Panel View Connect to +24VDC or -48VDC power sourceGround at power source 48 VDC Connect to Earth ground+24 VDC Ground at power source +24 VDC FeedConnect to the serial port of a PC Cabling the Serial Craft PortCabling the Ethernet Port Connect an Ethernet cable from a PC to ETH-1Connect a second clock source Connect a clock source Cabling the Network Synchronization PortCabling the Clock Ports on the Bits Chassis Cabling the Alarm Ports Cabling the Clock Ports on the ITU ChassisAlarm Input Sensing Pin NameAlarm Cut Off ACO Installing the NSP101 Control CardAlarm Output Reporting Insert one or two NSP101 cardsModule Red LED Module Green LED Status Top Bottom Active Green LED StatusETH Yellow LED Status Top #1 Bottom Alarm SUM Red LED StatusPWR Red LED #2 PWR Red LED #1 Status Top Bottom Installing the NIP400 Line Interface Card Insert NIP400 cards optionalConnect to DSX panels or punch down blocks Cabling the NIP400Clip NIP400 LED Indicators Port LED Port StateGrommets Insert NHP160 cards optional Installing the NHP160 Line Interface CardCabling and Inserting the NHP160 Line Interface Card NHP160 LED Indicators A yInstalling the BSP200 Line Interface Card BSP200 line terminationsConnect BNC coaxial cables BSP200 LED IndicatorsCabling the BSP200 Interface Red LED Interface Green Status Bottom LED Top Grommets Installing OSP155/ESP155/BCP155 Line Interface CardsInsert OSP155, ESP155, or BCP155 cards optional Cabling the OSP155 and BCP155 Installation OSP155, BCP155, and ESP155 LED Indicators Cabling the ESP155Attaching the Front Panel Applying Power to the Chassis W a yInstalling New Cards Maintaining BROADway HardwareInstalling Additional OSP155, ESP155 or BCP155 Cards Replacing Failed CardsMaintaining the Fan Tray Fan BoardConfiguration Configuration Default BROADway IP Address Assigning an IP Address to the BROADway SystemAssigning a Different IP Address ACT-USERNSP1234CUSTOMER,BROADWAYPS#configure PS#configure PSNSP-config#no interface bviPS#show BVI status bridge-group number PS#show bvi statusLocal SCP-1 Serial Craft Port Access Management Access to the BROADway SystemViewing Serial Craft Port Settings With the GUI Remote Modem SCP-1 Serial Craft Port AccessEthernet Port Command Line Access Ethernet Port Web Browser GUI AccessLogging In With the Web Browser Interface GUI EnterConfiguration Configuration Click here to minimize this window This window must remain running in the backgroundACT-USERNSP1234 Logging In With the Command Line Interface CLIACT-USERNSP1234username,password CANC-USERNSP1234Setting Up User Accounts User Account Management Using the GUI RTRV-USERNSP1234ACTIVE User Account Management Using TL1RTRV-USERNSP1234ALL RTRV-USERNSP1234MEENT-USERNSP1234joetech,mypassword,ADMIN,TL1 DLT-USERNSP1234usernameChanging Your Password Using TL1 Changing Your PasswordChanging Your Password Using the GUI Current Password field, type your current passwordSetting the Date and Time Using TL1 Setting the System Date and TimeSetting the Date and Time Using the GUI ED-DATNSP1234YY-MM-DD,HH-MM-SSSetting System Node Parameters Setting System Node Parameters Using the GUIExamples Setting System Node Parameters Using TL1RTRV-UDATANSP1234 ED-UDATANSP1234USED-EQPTNSP1234DIS RTRV-EQPTNSP-x.PWR-11234ED-EQPTNSP1234ENA Managing the BROADway Configuration Database Managing the Database Using the GUI CPY-DBNSP1RUNNING,SAVED,newdbname Managing the Database Using TL1RTRV-DBNSP1 CPY-DBNSP1SAVED,offlinenameExporting the BROADway Database to a TL1 Script Re-Starting the BROADway System Using TL1 Copying Files Between NSP101 ControllersUsing FTP with the BROADway System INIT-SYSNSP1234ALLNSP1 rtrv-sw-vernsp1234all Upgrading System SoftwareRtrv-sw-vernsp1234all Ftp put c\temp\bw308.zip \ftpFtp cd /FLASH NSP1 set-upgradensp1234bw308,all Set-upgrade command NSP1 set-upgradensp1234bw308Rolling Back a Software Update Upgrading the Boot ROMNSP1 exec-sysnsp1234bootUpdate NSP1 init-sysnsp1234FORCETL1 Software Upgrade Commands RTRV-SW-VERNSP1234ALLAppendix a SCP-1 and SCP-2 Connector Pinouts SCP-1 SCP-2 future use Pin Signal NameETH-1 and ETH-2 Connector Pinouts ETH-1 ETH-2 Pin SignalCKIN-1 and CKIN-2 Connector Pinouts Bits Only Pin SignalNIP400 Connector Pinouts NIP TX1-RX1, NIP TX2-RX2 T1/E1 NIP400 TX tip TX ring RX tip RX ring Circuit CardPorts and Cables Alarms Connector Pinouts Pin Color Name SignalNHP160 Connector Pinouts Scsi Pin Color SignalPorts and Cables Ports and Cables Index Index BROADway Release Index Index