Carrier Access 770-0125-AB installation manual Ethernet Port Command Line Access

Page 56

Configuration

Management Access to the BROADway System

Ethernet Port Command Line Access

1.Connect your PC or workstation to one of the Ethernet ports (see Cabling the Ethernet Port on page 2-9) and open a Telnet session to the IP address of the BROADway system (e.g. 169.254.0.1).

2.You should be presented with the LOGIN> prompt. Use CUSTOMER for the user name and BROADWAY as the password.

3.If you are successfully logged in, you will be presented with the NSP1> or NSP2> prompt.

4.You can now configure the BROADway system using the CLI interface. Follow the instructions in Logging In With the Command Line Interface (CLI) on page 3-13to learn how to log in and out of the system using the CLI or in Setting Up User Accounts on page 3-13.

NOTE: The BROADway system supports up to three simultaneous Telnet client sessions.

Ethernet Port Web Browser GUI Access

Connect your PC or workstation to one of the Ethernet ports on the BROADway and then follow the instructions found at Logging In With the Web Browser Interface (GUI) on page 3-9.

3-8	BROADway - Release 4.00

Image 56

Contents BROADway Page FCC Requirements, Part Safety of Information Technology EquipmentCompliance Card Service Framing Coding NetworkType JackIndustry Canada ICES-003 Industry Canada CS-03English FrenchSafety Information Electrostatic Discharge ESD Precautions Warranty Product Returns WarrantyLimitation of Warranty & Limitation of Remedies Third-Party Software Notices Sun Microsystems, Inc., Software NoticePreface Table of Contents Configuration Table of ContentsPorts and Cables IndexXiv BROADway Release Chapter Overview Installation Chassis Overview Top I/O Panel Front View of the Bits ChassisTop I/O Panel Front View of the ITU Chassis Mounting the Chassis in a Rack Mounting the Chassis in a RackSide View of the Chassis Cabling Power and Ground Extension PlateConnect to +24VDC or -48VDC power source Ground at power source 48 VDCBROADway Chassis Rear Panel View Connect to Earth ground+24 VDC Ground at power source +24 VDC FeedCabling the Serial Craft Port Cabling the Ethernet PortConnect to the serial port of a PC Connect an Ethernet cable from a PC to ETH-1Connect a second clock source Connect a clock source Cabling the Network Synchronization PortCabling the Clock Ports on the Bits Chassis Cabling the Alarm Ports Cabling the Clock Ports on the ITU ChassisAlarm Input Sensing Pin NameInstalling the NSP101 Control Card Alarm Output ReportingAlarm Cut Off ACO Insert one or two NSP101 cardsModule Red LED Module Green LED Status Top Bottom Active Green LED StatusETH Yellow LED Status Top #1 Bottom Alarm SUM Red LED StatusPWR Red LED #2 PWR Red LED #1 Status Top Bottom Installing the NIP400 Line Interface Card Insert NIP400 cards optionalConnect to DSX panels or punch down blocks Cabling the NIP400Clip NIP400 LED Indicators Port LED Port StateGrommets Insert NHP160 cards optional Installing the NHP160 Line Interface CardCabling and Inserting the NHP160 Line Interface Card NHP160 LED Indicators A yInstalling the BSP200 Line Interface Card BSP200 line terminationsConnect BNC coaxial cables BSP200 LED IndicatorsCabling the BSP200 Interface Red LED Interface Green Status Bottom LED Top Grommets Installing OSP155/ESP155/BCP155 Line Interface CardsInsert OSP155, ESP155, or BCP155 cards optional Cabling the OSP155 and BCP155 Installation OSP155, BCP155, and ESP155 LED Indicators Cabling the ESP155Attaching the Front Panel Applying Power to the Chassis W a yInstalling New Cards Maintaining BROADway HardwareInstalling Additional OSP155, ESP155 or BCP155 Cards Replacing Failed CardsMaintaining the Fan Tray Fan BoardConfiguration Configuration Default BROADway IP Address Assigning an IP Address to the BROADway SystemAssigning a Different IP Address ACT-USERNSP1234CUSTOMER,BROADWAYPS#configure PS#configure PSNSP-config#no interface bviPS#show BVI status bridge-group number PS#show bvi statusManagement Access to the BROADway System Viewing Serial Craft Port Settings With the GUILocal SCP-1 Serial Craft Port Access Remote Modem SCP-1 Serial Craft Port AccessEthernet Port Command Line Access Ethernet Port Web Browser GUI AccessLogging In With the Web Browser Interface GUI EnterConfiguration Configuration Click here to minimize this window This window must remain running in the backgroundLogging In With the Command Line Interface CLI ACT-USERNSP1234username,passwordACT-USERNSP1234 CANC-USERNSP1234Setting Up User Accounts User Account Management Using the GUI User Account Management Using TL1 RTRV-USERNSP1234ALLRTRV-USERNSP1234ACTIVE RTRV-USERNSP1234MEENT-USERNSP1234joetech,mypassword,ADMIN,TL1 DLT-USERNSP1234usernameChanging Your Password Changing Your Password Using the GUIChanging Your Password Using TL1 Current Password field, type your current passwordSetting the System Date and Time Setting the Date and Time Using the GUISetting the Date and Time Using TL1 ED-DATNSP1234YY-MM-DD,HH-MM-SSSetting System Node Parameters Setting System Node Parameters Using the GUISetting System Node Parameters Using TL1 RTRV-UDATANSP1234Examples ED-UDATANSP1234USED-EQPTNSP1234DIS RTRV-EQPTNSP-x.PWR-11234ED-EQPTNSP1234ENA Managing the BROADway Configuration Database Managing the Database Using the GUI Managing the Database Using TL1 RTRV-DBNSP1CPY-DBNSP1RUNNING,SAVED,newdbname CPY-DBNSP1SAVED,offlinenameExporting the BROADway Database to a TL1 Script Re-Starting the BROADway System Using TL1 Copying Files Between NSP101 ControllersUsing FTP with the BROADway System INIT-SYSNSP1234ALLNSP1 rtrv-sw-vernsp1234all Upgrading System SoftwareRtrv-sw-vernsp1234all Ftp put c\temp\bw308.zip \ftpFtp cd /FLASH NSP1 set-upgradensp1234bw308,all Set-upgrade command NSP1 set-upgradensp1234bw308Rolling Back a Software Update Upgrading the Boot ROMNSP1 exec-sysnsp1234bootUpdate NSP1 init-sysnsp1234FORCETL1 Software Upgrade Commands RTRV-SW-VERNSP1234ALLAppendix a SCP-1 and SCP-2 Connector Pinouts SCP-1 SCP-2 future use Pin Signal NameETH-1 and ETH-2 Connector Pinouts ETH-1 ETH-2 Pin SignalCKIN-1 and CKIN-2 Connector Pinouts Bits Only Pin SignalNIP400 Connector Pinouts NIP TX1-RX1, NIP TX2-RX2 T1/E1 NIP400 TX tip TX ring RX tip RX ring Circuit CardPorts and Cables Alarms Connector Pinouts Pin Color Name SignalNHP160 Connector Pinouts Scsi Pin Color SignalPorts and Cables Ports and Cables Index Index BROADway Release Index Index