Carrier Access 770-0125-AB Interface Red LED Interface Green Status Bottom LED Top

Page 39

Installation

Installing the BSP200 Line Interface Card

If the card failure sequence is displayed, remove the card and re-insert it into the chassis. If the card failure sequence is still displayed, then replace the card.

Line status (per port):

INTERFACE Red LED	INTERFACE Green	Status
(Bottom)	LED (Top)	Status
(Bottom)	LED (Top)

Off	Off	The card is not configured, or
		alarm reporting is disabled on the
		interface

Off	On	Interface operating normally

Off	Blinking	Interface performing a diagnostic
		test

On	Off	Interface failure (LOS, OOF, AIS)

Blinking	Off	Yellow alarm (RAI)

On	On	Interface initializing during system
		power up

BROADway - Release 4.00

2-23

Image 39

Contents BROADway Page Safety of Information Technology Equipment ComplianceFCC Requirements, Part Jack Card Service Framing CodingNetwork TypeFrench Industry Canada ICES-003Industry Canada CS-03 EnglishSafety Information Electrostatic Discharge ESD Precautions Warranty Limitation of Warranty & Limitation of RemediesWarranty Product Returns Sun Microsystems, Inc., Software Notice Third-Party Software NoticesPreface Table of Contents Table of Contents ConfigurationIndex Ports and CablesXiv BROADway Release Chapter Overview Installation Top I/O Panel Front View of the Bits Chassis Chassis OverviewTop I/O Panel Front View of the ITU Chassis Mounting the Chassis in a Rack Mounting the Chassis in a RackSide View of the Chassis Extension Plate Cabling Power and GroundConnect to Earth ground Connect to +24VDC or -48VDC power sourceGround at power source 48 VDC BROADway Chassis Rear Panel View+24 VDC Feed +24 VDC Ground at power sourceConnect an Ethernet cable from a PC to ETH-1 Cabling the Serial Craft PortCabling the Ethernet Port Connect to the serial port of a PCCabling the Network Synchronization Port Cabling the Clock Ports on the Bits ChassisConnect a second clock source Connect a clock source Cabling the Clock Ports on the ITU Chassis Cabling the Alarm PortsPin Name Alarm Input SensingInsert one or two NSP101 cards Installing the NSP101 Control CardAlarm Output Reporting Alarm Cut Off ACOActive Green LED Status Module Red LED Module Green LED Status Top BottomAlarm SUM Red LED Status PWR Red LED #2 PWR Red LED #1 Status Top BottomETH Yellow LED Status Top #1 Bottom Insert NIP400 cards optional Installing the NIP400 Line Interface CardCabling the NIP400 ClipConnect to DSX panels or punch down blocks Port LED Port State NIP400 LED IndicatorsInstalling the NHP160 Line Interface Card Cabling and Inserting the NHP160 Line Interface CardGrommets Insert NHP160 cards optional A y NHP160 LED IndicatorsBSP200 line terminations Installing the BSP200 Line Interface CardBSP200 LED Indicators Cabling the BSP200Connect BNC coaxial cables Interface Red LED Interface Green Status Bottom LED Top Installing OSP155/ESP155/BCP155 Line Interface Cards Insert OSP155, ESP155, or BCP155 cards optionalGrommets Cabling the OSP155 and BCP155 Installation Cabling the ESP155 OSP155, BCP155, and ESP155 LED IndicatorsAttaching the Front Panel W a y Applying Power to the ChassisMaintaining BROADway Hardware Installing New CardsReplacing Failed Cards Installing Additional OSP155, ESP155 or BCP155 CardsFan Board Maintaining the Fan TrayConfiguration Configuration Assigning an IP Address to the BROADway System Default BROADway IP AddressACT-USERNSP1234CUSTOMER,BROADWAY Assigning a Different IP AddressPS#configure PSNSP-config#no interface bvi PS#configurePS#show bvi status PS#show BVI status bridge-group numberRemote Modem SCP-1 Serial Craft Port Access Management Access to the BROADway SystemViewing Serial Craft Port Settings With the GUI Local SCP-1 Serial Craft Port AccessEthernet Port Web Browser GUI Access Ethernet Port Command Line AccessEnter Logging In With the Web Browser Interface GUIConfiguration Configuration This window must remain running in the background Click here to minimize this windowCANC-USERNSP1234 Logging In With the Command Line Interface CLIACT-USERNSP1234username,password ACT-USERNSP1234Setting Up User Accounts User Account Management Using the GUI RTRV-USERNSP1234ME User Account Management Using TL1RTRV-USERNSP1234ALL RTRV-USERNSP1234ACTIVEDLT-USERNSP1234username ENT-USERNSP1234joetech,mypassword,ADMIN,TL1Current Password field, type your current password Changing Your PasswordChanging Your Password Using the GUI Changing Your Password Using TL1ED-DATNSP1234YY-MM-DD,HH-MM-SS Setting the System Date and TimeSetting the Date and Time Using the GUI Setting the Date and Time Using TL1Setting System Node Parameters Using the GUI Setting System Node ParametersED-UDATANSP1234US Setting System Node Parameters Using TL1RTRV-UDATANSP1234 ExamplesRTRV-EQPTNSP-x.PWR-11234 ED-EQPTNSP1234ENAED-EQPTNSP1234DIS Managing the BROADway Configuration Database Managing the Database Using the GUI CPY-DBNSP1SAVED,offlinename Managing the Database Using TL1RTRV-DBNSP1 CPY-DBNSP1RUNNING,SAVED,newdbnameExporting the BROADway Database to a TL1 Script Copying Files Between NSP101 Controllers Re-Starting the BROADway System Using TL1INIT-SYSNSP1234ALL Using FTP with the BROADway SystemUpgrading System Software Rtrv-sw-vernsp1234allNSP1 rtrv-sw-vernsp1234all \ftp Ftp cd /FLASHFtp put c\temp\bw308.zip Set-upgrade command NSP1 set-upgradensp1234bw308 NSP1 set-upgradensp1234bw308,allUpgrading the Boot ROM Rolling Back a Software UpdateNSP1 init-sysnsp1234FORCE NSP1 exec-sysnsp1234bootUpdateRTRV-SW-VERNSP1234ALL TL1 Software Upgrade CommandsAppendix a SCP-1 SCP-2 future use Pin Signal Name SCP-1 and SCP-2 Connector PinoutsETH-1 ETH-2 Pin Signal ETH-1 and ETH-2 Connector PinoutsPin Signal CKIN-1 and CKIN-2 Connector Pinouts Bits OnlyT1/E1 NIP400 TX tip TX ring RX tip RX ring Circuit Card NIP400 Connector Pinouts NIP TX1-RX1, NIP TX2-RX2Ports and Cables Pin Color Name Signal Alarms Connector PinoutsScsi Pin Color Signal NHP160 Connector PinoutsPorts and Cables Ports and Cables Index Index BROADway Release Index Index

INTERFACE Red LED

INTERFACE Green

Status

(Bottom)

LED (Top)