Carrier Access 770-0125-AB PS#show BVI status bridge-group number, PS#show bvi status

Page 54

Configuration

Assigning an IP Address to the BROADway System

To change the state of the BVI to “up”, use the following PS commands:

PS#configure

PS(NSP-config)#interface bvi 1

PS(NSP-config-bvi)#no shutdown

To display the status of the BVI, use the following PS command:

PS#show BVI status [bridge-group number]

If you specify an optional [bridge-group number], only the BVI associated with the [bridge-group number] will be displayed. If you leave the [bridge-group number] field blank, all of the configured BVIs will be displayed.

The following sample output shows the show BVI status command results:

PS#show bvi status

BVI is configured for this bridge group

BVI is administratively enabled

MAC address of BVI is 00-02-35-00-ca-e8

3-6	BROADway - Release 4.00

Image 54

Contents BROADway Page Safety of Information Technology Equipment ComplianceFCC Requirements, Part Type Card Service Framing CodingNetwork JackEnglish Industry Canada ICES-003Industry Canada CS-03 FrenchSafety Information Electrostatic Discharge ESD Precautions Warranty Limitation of Warranty & Limitation of RemediesWarranty Product Returns Third-Party Software Notices Sun Microsystems, Inc., Software NoticePreface Table of Contents Configuration Table of ContentsPorts and Cables IndexXiv BROADway Release Chapter Overview Installation Chassis Overview Top I/O Panel Front View of the Bits ChassisTop I/O Panel Front View of the ITU Chassis Mounting the Chassis in a Rack Mounting the Chassis in a RackSide View of the Chassis Cabling Power and Ground Extension PlateBROADway Chassis Rear Panel View Connect to +24VDC or -48VDC power sourceGround at power source 48 VDC Connect to Earth ground+24 VDC Ground at power source +24 VDC FeedConnect to the serial port of a PC Cabling the Serial Craft PortCabling the Ethernet Port Connect an Ethernet cable from a PC to ETH-1Cabling the Network Synchronization Port Cabling the Clock Ports on the Bits ChassisConnect a second clock source Connect a clock source Cabling the Alarm Ports Cabling the Clock Ports on the ITU ChassisAlarm Input Sensing Pin NameAlarm Cut Off ACO Installing the NSP101 Control CardAlarm Output Reporting Insert one or two NSP101 cardsModule Red LED Module Green LED Status Top Bottom Active Green LED StatusAlarm SUM Red LED Status PWR Red LED #2 PWR Red LED #1 Status Top BottomETH Yellow LED Status Top #1 Bottom Installing the NIP400 Line Interface Card Insert NIP400 cards optionalCabling the NIP400 ClipConnect to DSX panels or punch down blocks NIP400 LED Indicators Port LED Port StateInstalling the NHP160 Line Interface Card Cabling and Inserting the NHP160 Line Interface CardGrommets Insert NHP160 cards optional NHP160 LED Indicators A yInstalling the BSP200 Line Interface Card BSP200 line terminationsBSP200 LED Indicators Cabling the BSP200Connect BNC coaxial cables Interface Red LED Interface Green Status Bottom LED Top Installing OSP155/ESP155/BCP155 Line Interface Cards Insert OSP155, ESP155, or BCP155 cards optionalGrommets Cabling the OSP155 and BCP155 Installation OSP155, BCP155, and ESP155 LED Indicators Cabling the ESP155Attaching the Front Panel Applying Power to the Chassis W a yInstalling New Cards Maintaining BROADway HardwareInstalling Additional OSP155, ESP155 or BCP155 Cards Replacing Failed CardsMaintaining the Fan Tray Fan BoardConfiguration Configuration Default BROADway IP Address Assigning an IP Address to the BROADway SystemAssigning a Different IP Address ACT-USERNSP1234CUSTOMER,BROADWAYPS#configure PS#configure PSNSP-config#no interface bviPS#show BVI status bridge-group number PS#show bvi statusLocal SCP-1 Serial Craft Port Access Management Access to the BROADway SystemViewing Serial Craft Port Settings With the GUI Remote Modem SCP-1 Serial Craft Port AccessEthernet Port Command Line Access Ethernet Port Web Browser GUI AccessLogging In With the Web Browser Interface GUI EnterConfiguration Configuration Click here to minimize this window This window must remain running in the backgroundACT-USERNSP1234 Logging In With the Command Line Interface CLIACT-USERNSP1234username,password CANC-USERNSP1234Setting Up User Accounts User Account Management Using the GUI RTRV-USERNSP1234ACTIVE User Account Management Using TL1RTRV-USERNSP1234ALL RTRV-USERNSP1234MEENT-USERNSP1234joetech,mypassword,ADMIN,TL1 DLT-USERNSP1234usernameChanging Your Password Using TL1 Changing Your PasswordChanging Your Password Using the GUI Current Password field, type your current passwordSetting the Date and Time Using TL1 Setting the System Date and TimeSetting the Date and Time Using the GUI ED-DATNSP1234YY-MM-DD,HH-MM-SSSetting System Node Parameters Setting System Node Parameters Using the GUIExamples Setting System Node Parameters Using TL1RTRV-UDATANSP1234 ED-UDATANSP1234USRTRV-EQPTNSP-x.PWR-11234 ED-EQPTNSP1234ENAED-EQPTNSP1234DIS Managing the BROADway Configuration Database Managing the Database Using the GUI CPY-DBNSP1RUNNING,SAVED,newdbname Managing the Database Using TL1RTRV-DBNSP1 CPY-DBNSP1SAVED,offlinenameExporting the BROADway Database to a TL1 Script Re-Starting the BROADway System Using TL1 Copying Files Between NSP101 ControllersUsing FTP with the BROADway System INIT-SYSNSP1234ALLUpgrading System Software Rtrv-sw-vernsp1234allNSP1 rtrv-sw-vernsp1234all \ftp Ftp cd /FLASHFtp put c\temp\bw308.zip NSP1 set-upgradensp1234bw308,all Set-upgrade command NSP1 set-upgradensp1234bw308Rolling Back a Software Update Upgrading the Boot ROMNSP1 exec-sysnsp1234bootUpdate NSP1 init-sysnsp1234FORCETL1 Software Upgrade Commands RTRV-SW-VERNSP1234ALLAppendix a SCP-1 and SCP-2 Connector Pinouts SCP-1 SCP-2 future use Pin Signal NameETH-1 and ETH-2 Connector Pinouts ETH-1 ETH-2 Pin SignalCKIN-1 and CKIN-2 Connector Pinouts Bits Only Pin SignalNIP400 Connector Pinouts NIP TX1-RX1, NIP TX2-RX2 T1/E1 NIP400 TX tip TX ring RX tip RX ring Circuit CardPorts and Cables Alarms Connector Pinouts Pin Color Name SignalNHP160 Connector Pinouts Scsi Pin Color SignalPorts and Cables Ports and Cables Index Index BROADway Release Index Index