Connect Tech CTIM-00043 Example #3, 0x340 = XXXX.XXXX.XXXX.X 011.01CJ.JJJJ binary, Example #4

Page 11

CANpro/104 User Manual

Example #2: Memory Address 0x0C8000 (this address is below the 1-Meg boundary) 0x0C8000 = 0000.1100.100X.XXXX.CJJJ.JJJJ (binary)

	Address	Bit	J3A or J3B	Installed
	Bit	Value	Position	or Removed
	23	0	J3A-2	Removed
	22	0	J3A-3	Removed
	21	0	Address Bit always decoded as “0”
	20	0	Address Bit always decoded as “0”
	19	1	J3A-4	Installed
	18	1	J3A-5	Installed
	17	0	J3A-6	Removed
	16	0	J3B-1	Removed
	15	1	J3B-2	Installed
	14	0	J3B-3	Removed
	13	0	J3B-4	Removed
	Table 9
Example #3:	I/O Address 0x340 (BasicCAN mode)
	0x340 = XXXX.XXXX.XXXX.X011.01CJ.JJJJ (binary)

	Address	Bit	J3A or J3B	Installed
	Bit	Value	Position	or Removed
	23 -> 11	X	---	---
	10	0	J3A-6	Removed
	9	1	J3B-1	Installed
	8	1	J3B-2	Installed
	7	0	J3B-3	Removed
	6	1	J3B-4	Installed
	Table 10
Example #4:	I/O Address 0x600 (PeliCAN mode)
	0x600 = XXXX.XXXX.XXXX.X110.CJJJ.JJJJ (binary)

	Address	Bit	J3A or J3B	Installed
	Bit	Value	Position	or Removed
	23 -> 11	X	---	---
	10	1	J3A-6	Installed
	9	1	J3B-1	Installed
	8	0	J3B-2	Removed

Table 11

11	www.connecttech.com	CTIM-00043 (0.01) 1/15/2010
	800-426-8979 519-836-1291

Image 11

Contents CTIM-00043 0.02 January 15 CANpro/104Table of Contents CTIM-00043 0.01 1/15/2010 Revision History Copyright NoticeTrademark Acknowledgement Introduction FeaturesMemory Space Hardware Installation Rev C & LaterMemory vs I/O Spaces J3A Position #1 Function CTI CANpro/104 SpacesSpace Memory Space EnablingJumper Memory Space Position Address Bit Group Base Address DecodingAddress Position #5 Position #6 Position #7When I/O Space is selected When Memory Space is selectedJ3C Position #2 Function Address Bit J3A or J3B Installed Value Position Or RemovedPeliCAN vs BasicCAN Addressing Modes Addressing Examples0x600 = XXXX.XXXX.XXXX.X 110.CJJJ.JJJJ binary Example #30x340 = XXXX.XXXX.XXXX.X 011.01CJ.JJJJ binary Example #4Can Controller Addressing Table Memory Address Common Memory Space Address SelectionsBase Can Bus Options Interrupt Mode and Selections9D Connector Shell Ground Performance EnhancementCan Bus Dominant Timeout and Minimum Speed Single Interrupt ModeDual Interrupt Mode Shared Interrupt ModeJumper Summaries Security ID FeaturePosition Function Jumper Installed Jumper Removed J4 and J5 J3BCANpro/104 Opto Diagrams Hardware Installation Rev a & BNo Interrupts Interrupts and Memory I/O Range SelectionUnique Interrupt Lines Sharing a Single Interrupt LineCan Address Mode and Range SelectionInterrupt Sharing Other On-board Jumper Selection 10-pin Header Pinouts Pin No Signal Connector PinoutsDB-9 Cable Connector Pinouts Pin No Signal Certification for CANpro/104 SpecificationsCertification Email/Internet Mail/Courier Telephone/Facsimile