B&B Electronics EIR618-2SFP-T manual Security, 802.1X/Radius Configuration

Page 106

Security

802.1X/Radius Configuration

802.1x is an IEEE authentication specification that allows a client to connect to a wireless access point or wired switch but prevents the client from gaining access to the Internet until it proves authority by providing a user name and password, which is verified by a separate server.

System Configuration

1.IEEE 802.1x Protocol: Enable or disable 802.1x protocol.

2.Radius Server IP: Enter the Radius Server IP address.

3.Server Port: Enter the UDP destination port for authentication requests to the Radius Server.

4.Accounting Port: Enter the UDP destination port for accounting requests to the Radius Server.

5.Shared Key: Enter an encryption key for use during authentication sessions. This key must match the encryption key used on the Radius Server

6.NAS, Identifier: Enter the identifier of the radius client.

7.Click Apply

802.1x System Configuration interface

94	Manual Documentation Number: EIR618-2SFP-T_5107m
	Manual Documentation Number: EIR618-2SFP-T_5107m
	B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax	815-433-5104 – www.bb-elec.com
	B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444	– Fax +353 91-792445 – www.bb-europe.com

Image 106

Contents Product Description Page Eighteen Port Managed Industrial Ethernet Switches Kernel Version Firmware VersionV1.07 V2.07FCC Warning Page Content Console Management About Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 101 102Page Features Introduction¾ Port Based Vlan ¾ 802.1 Q Tag Vlan ¾ GvrpPort Trunk with Software SpecificationManagement Spanning treeLogin Security Quality of serviceClass of service Relay AlarmPackage Contents Front Panel Physical DimensionFront Panel of the industrial switch D x H 2.83 x 4.13 x 5.98 in 7.2mm x 10.5mm x 15.2 cmTop Panel of the industrial switch Top ViewLED Indicators Ports Straight Through Cable Schematic Cross Over Cable Schematic „ Gigabit Copper/SFP Mini-GBIC combo portCabling Insert the fiber cable into the transceiver Remove LC connector Wiring the Power Inputs Wiring the Fault Alarm Contact Rear Panel of the switch DIN-Rail DIN-Rail MountingManual Documentation Number EIR618-2SFP-T5107m Panel Mounting Hardware Installation Installation StepsNetwork Application Ring ApplicationCoupling Ring Application Dual Homing Application Pin Assignment Connecting to the Console PortDB9 Connector RJ-45 Connector Orange/White Green/White Blue Blue/White Brown/WhiteLogin in the Console Interface Settings of communication parametersCLI command interface Console login interfaceCLI Management Commands Level System Name Commands Set ListSystem Commands Set System LocationIp-address PasswordSystem Contact Subnet-maskHours IP addressFull half Port Commands SetPortid 101001000autoEnable Disable ValueTrunk Commands Set Vlan Commands Set GroupIDGroupName Group NamePortNumbers PortNumber~61440 Spanning Tree Commands SetSeconds Forward-time seconds Spanning-treeHello-time seconds Stp-path-costAutoTrueFalse TrueFalseQOS Commands Set Igmp Commands SetMac / Filter Table Commands Set Snmp Commands Set ExactPrifix NameNoAuthNoPrivAuthNoP RivAuthPriv Read View Name Write View Name Notify ViewMibview table Port Mirroring Commands SetRemove specified View Name SNMPV3 agentPort ID 802.1x Commands SetWords Sec Disable reject acceptNumber SystemLog, Smtp and Event Commands Set Tftp Commands SetAuthorize Index Email address ClientserverbothAccount SystemlogSMTPBothSntp Commands Set Start time End timeTimezone Ring Commands SetMinute 1st Ring Port 2nd RingControl Port Coupling PortDual Homing Port About Web-based Management Preparing for Web ManagementSystem Login System Information System information interfaceIP Configuration IP configuration interfaceDhcp Server Client Entries Dhcp Server System configurationDhcp Server Configuration interface Dhcp Client information is displayedDhcp Client Entries interface Dhcp Server Port and IP BindingsPort and IP Bindings interface Update Firmware interface Tftp Update FirmwareTftp Restore Configuration Restore Configuration interfaceSystem Event Log Syslog Configuration Tftp Backup ConfigurationTftp Server IP Address Enter the Tftp server IP System Event Log Smtp Configuration Syslog Configuration interfaceSystem Event Log Event Configuration Smtp Configuration interfaceEvent Configuration interface Sntp Configuration Fault Relay AlarmFault Relay Alarm interface Local Time Zone Conversion from UTC Time at 1200 UTC Switch Timer Displays the current time Click Apply Daylight Saving Offset mins Enter the offset in minutesSntp Configuration interface IP SecurityUser Authentication interface User AuthenticationIP Security interface Port Statistics Port Statistics interfacePort Control Button to add Aggregator settingPort Trunk Port. To remove unwanted ports, select Port and clickDelete to delete Trunk Group State Activity Aggregator InformationDisplays static trunk group information Port Trunk State Activity interface Port Mirroring Port Trunk Port Mirroring interfaceRate Limiting Rate Limiting interfaceVlan configuration Port-based Vlan Vlan configurationVlan Configuration interface Vlan Port Based interface VLAN-Port Based Add interfaceMembers of the existing Vlan group Use Button to delete the VlanUse Button to modify group name, Vlan ID, or add/remove VLAN-Port Based Edit/Delete interface„ Hybrid Link Both Access Link and Trunk Link 802.1Q VlanGroup Configuration 802.1Q Vlan interface„ You can modify the Vlan group name and Vlan ID Group Configuration interface„ Click Apply button Rstp System Configuration Rapid Spanning TreeRstp Port Configuration Rstp System Configuration interfaceRstp Port Configuration interface System Configuration Snmp Configuration„ Community Strings Trap Configuration Snmp System Configuration interfaceContext Table SNMPV3 Configuration„ Privacy Password Enter the private password User ProfileSnmp V3 configuration interface Group Table Access TableMIBview Table „ Click Remove to remove an unwanted context name QoS ConfigurationQoS Policy and Priority Type „ QoS Policy select the QoS policy ruleQoS Configuration interface Port-based PriorityTOS Configuration Igmp ConfigurationCOS Configuration „ Click Apply button to make the settings effectiveQuery Message sent from the querier Igmp router or switchMessage Description ReportRing Ring Interface 802.1x System Configuration interface 802.1X/Radius ConfigurationSecurity 802.1x Port Configuration 802.1x Per Port Setting interfaceMisc Configuration 802.1x Misc Configuration interfaceMAC Address Table Use the MAC address table to ensure the port securityStatic MAC Addresses interface MAC Filtering interfaceFactory Default All MAC Address interfaceClick Save to save the configuration to the flash memory Save ConfigurationSystem Reboot Click Reboot to reboot the systemTrouble shooting 101Transfer Rate StandardProtocol MAC addressPower „ LC Single mode 9/125um Back-planePower Supply Consumption InstallCE/EN60950-1 IEC60068-2-32 Free fall SafetyStability testing IEC60068-2-27 Shock IEC60068-2-6 Vibration