B&B Electronics EIR618-2SFP-T manual FCC Warning

Page 5

FCC Warning

This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class-A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Image 5

Contents Product Description Page Eighteen Port Managed Industrial Ethernet Switches V1.07 Firmware VersionKernel Version V2.07FCC Warning Page Content Console Management About Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 102 101Page Introduction Features¾ Gvrp ¾ Port Based Vlan ¾ 802.1 Q Tag VlanManagement Software SpecificationPort Trunk with Spanning treeClass of service Quality of serviceLogin Security Relay AlarmPackage Contents Front Panel of the industrial switch Physical DimensionFront Panel D x H 2.83 x 4.13 x 5.98 in 7.2mm x 10.5mm x 15.2 cmTop View Top Panel of the industrial switchLED Indicators Ports „ Gigabit Copper/SFP Mini-GBIC combo port Straight Through Cable Schematic Cross Over Cable SchematicCabling Insert the fiber cable into the transceiver Remove LC connector Wiring the Power Inputs Wiring the Fault Alarm Contact DIN-Rail Mounting Rear Panel of the switch DIN-RailManual Documentation Number EIR618-2SFP-T5107m Panel Mounting Installation Steps Hardware InstallationRing Application Network ApplicationCoupling Ring Application Dual Homing Application DB9 Connector RJ-45 Connector Connecting to the Console PortPin Assignment Orange/White Green/White Blue Blue/White Brown/WhiteSettings of communication parameters Login in the Console InterfaceCLI Management Console login interfaceCLI command interface Commands Level System Commands Set Commands Set ListSystem Name System LocationSystem Contact PasswordIp-address Subnet-maskIP address HoursPortid Port Commands SetFull half 101001000autoValue Enable DisableTrunk Commands Set GroupID Vlan Commands SetPortNumbers Group NameGroupName PortNumberSeconds Spanning Tree Commands Set~61440 Hello-time seconds Spanning-treeForward-time seconds Stp-path-costTrueFalse AutoTrueFalseIgmp Commands Set QOS Commands SetMac / Filter Table Commands Set Snmp Commands Set NoAuthNoPrivAuthNoP RivAuthPriv NameExactPrifix Read View Name Write View Name Notify ViewRemove specified Port Mirroring Commands SetMibview table View Name SNMPV3 agentWords 802.1x Commands SetPort ID Number Disable reject acceptSec Authorize Tftp Commands SetSystemLog, Smtp and Event Commands Set Account ClientserverbothIndex Email address SystemlogSMTPBothStart time End time Sntp Commands SetMinute Ring Commands SetTimezone 1st Ring Port 2nd RingDual Homing Port Coupling PortControl Port Preparing for Web Management About Web-based ManagementSystem Login System information interface System InformationIP configuration interface IP ConfigurationDhcp Server Configuration interface Dhcp Server System configurationDhcp Server Client Entries Dhcp Client information is displayedPort and IP Bindings interface Dhcp Server Port and IP BindingsDhcp Client Entries interface Tftp Restore Configuration Tftp Update FirmwareUpdate Firmware interface Restore Configuration interfaceTftp Server IP Address Enter the Tftp server IP Tftp Backup ConfigurationSystem Event Log Syslog Configuration Syslog Configuration interface System Event Log Smtp ConfigurationSmtp Configuration interface System Event Log Event ConfigurationEvent Configuration interface Fault Relay Alarm interface Fault Relay AlarmSntp Configuration Local Time Zone Conversion from UTC Time at 1200 UTC Daylight Saving Offset mins Enter the offset in minutes Switch Timer Displays the current time Click ApplyIP Security Sntp Configuration interfaceIP Security interface User AuthenticationUser Authentication interface Port Statistics interface Port StatisticsPort Control Port Trunk Aggregator settingButton to add Port. To remove unwanted ports, select Port and clickDelete to delete Trunk Group Displays static trunk group information Aggregator InformationState Activity Port Trunk State Activity interface Port Trunk Port Mirroring interface Port MirroringRate Limiting interface Rate LimitingVlan Configuration interface Vlan configurationVlan configuration Port-based Vlan VLAN-Port Based Add interface Vlan Port Based interfaceUse Button to modify group name, Vlan ID, or add/remove Use Button to delete the VlanMembers of the existing Vlan group VLAN-Port Based Edit/Delete interface802.1Q Vlan „ Hybrid Link Both Access Link and Trunk Link802.1Q Vlan interface Group Configuration„ Click Apply button Group Configuration interface„ You can modify the Vlan group name and Vlan ID Rapid Spanning Tree Rstp System ConfigurationRstp System Configuration interface Rstp Port ConfigurationRstp Port Configuration interface „ Community Strings Snmp ConfigurationSystem Configuration Snmp System Configuration interface Trap Configuration„ Privacy Password Enter the private password SNMPV3 ConfigurationContext Table User ProfileSnmp V3 configuration interface MIBview Table Access TableGroup Table QoS Policy and Priority Type QoS Configuration„ Click Remove to remove an unwanted context name „ QoS Policy select the QoS policy rulePort-based Priority QoS Configuration interfaceCOS Configuration Igmp ConfigurationTOS Configuration „ Click Apply button to make the settings effectiveMessage Description Message sent from the querier Igmp router or switchQuery ReportRing Ring Interface Security 802.1X/Radius Configuration802.1x System Configuration interface 802.1x Per Port Setting interface 802.1x Port Configuration802.1x Misc Configuration interface Misc ConfigurationUse the MAC address table to ensure the port security MAC Address TableMAC Filtering interface Static MAC Addresses interfaceAll MAC Address interface Factory DefaultSystem Reboot Save ConfigurationClick Save to save the configuration to the flash memory Click Reboot to reboot the system101 Trouble shootingProtocol StandardTransfer Rate MAC addressPower Supply „ LC Single mode 9/125um Back-planePower Consumption InstallStability testing SafetyCE/EN60950-1 IEC60068-2-32 Free fall IEC60068-2-27 Shock IEC60068-2-6 Vibration