B&B Electronics EIR618-2SFP-T manual Hardware Installation, Installation Steps

Page 31

Hardware Installation

Installation Steps

1.Unpack the Industrial switch.

2.Ensure the DIN-Rail is tightly screwed to the Industrial switch. If not, refer to DIN-Rail Mounting section for DIN-Rail installation. To panel mount the Industrial switch, refer to Panel Mounting section.

3.Apply power to the switch (refer to the Wiring the Power Inputs section). The power LED will light.

4.Connect CAT 5 cables to the Industrial switch’s RJ-45 ports and to the network devices

[NOTE] If the network devices do not support MID/MDIX, a crossover cable may be required.

Manual Documentation Number: EIR618-2SFP-T_5107m

19

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

Image 31

Contents Product Description Page Eighteen Port Managed Industrial Ethernet Switches V2.07 Firmware VersionV1.07 Kernel VersionFCC Warning Page Content Console Management About Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 102 101Page Introduction Features¾ Gvrp ¾ Port Based Vlan ¾ 802.1 Q Tag VlanSpanning tree Software SpecificationManagement Port Trunk withRelay Alarm Quality of serviceClass of service Login SecurityPackage Contents D x H 2.83 x 4.13 x 5.98 in 7.2mm x 10.5mm x 15.2 cm Physical DimensionFront Panel of the industrial switch Front PanelTop View Top Panel of the industrial switchLED Indicators Ports „ Gigabit Copper/SFP Mini-GBIC combo port Straight Through Cable Schematic Cross Over Cable SchematicCabling Insert the fiber cable into the transceiver Remove LC connector Wiring the Power Inputs Wiring the Fault Alarm Contact DIN-Rail Mounting Rear Panel of the switch DIN-RailManual Documentation Number EIR618-2SFP-T5107m Panel Mounting Installation Steps Hardware InstallationRing Application Network ApplicationCoupling Ring Application Dual Homing Application Orange/White Green/White Blue Blue/White Brown/White Connecting to the Console PortDB9 Connector RJ-45 Connector Pin AssignmentSettings of communication parameters Login in the Console InterfaceCLI command interface Console login interfaceCLI Management Commands Level System Location Commands Set ListSystem Commands Set System NameSubnet-mask PasswordSystem Contact Ip-addressIP address Hours101001000auto Port Commands SetPortid Full halfValue Enable DisableTrunk Commands Set GroupID Vlan Commands SetPortNumber Group NamePortNumbers GroupName~61440 Spanning Tree Commands SetSeconds Stp-path-cost Spanning-treeHello-time seconds Forward-time secondsTrueFalse AutoTrueFalseIgmp Commands Set QOS Commands SetMac / Filter Table Commands Set Snmp Commands Set Read View Name Write View Name Notify View NameNoAuthNoPrivAuthNoP RivAuthPriv ExactPrifixView Name SNMPV3 agent Port Mirroring Commands SetRemove specified Mibview tablePort ID 802.1x Commands SetWords Sec Disable reject acceptNumber SystemLog, Smtp and Event Commands Set Tftp Commands SetAuthorize SystemlogSMTPBoth ClientserverbothAccount Index Email addressStart time End time Sntp Commands Set1st Ring Port 2nd Ring Ring Commands SetMinute TimezoneControl Port Coupling PortDual Homing Port Preparing for Web Management About Web-based ManagementSystem Login System information interface System InformationIP configuration interface IP ConfigurationDhcp Client information is displayed Dhcp Server System configurationDhcp Server Configuration interface Dhcp Server Client EntriesDhcp Client Entries interface Dhcp Server Port and IP BindingsPort and IP Bindings interface Restore Configuration interface Tftp Update FirmwareTftp Restore Configuration Update Firmware interfaceSystem Event Log Syslog Configuration Tftp Backup ConfigurationTftp Server IP Address Enter the Tftp server IP Syslog Configuration interface System Event Log Smtp ConfigurationSmtp Configuration interface System Event Log Event ConfigurationEvent Configuration interface Sntp Configuration Fault Relay AlarmFault Relay Alarm interface Local Time Zone Conversion from UTC Time at 1200 UTC Daylight Saving Offset mins Enter the offset in minutes Switch Timer Displays the current time Click ApplyIP Security Sntp Configuration interfaceUser Authentication interface User AuthenticationIP Security interface Port Statistics interface Port StatisticsPort Control Port. To remove unwanted ports, select Port and click Aggregator settingPort Trunk Button to addDelete to delete Trunk Group State Activity Aggregator InformationDisplays static trunk group information Port Trunk State Activity interface Port Trunk Port Mirroring interface Port MirroringRate Limiting interface Rate LimitingVlan configuration Port-based Vlan Vlan configurationVlan Configuration interface VLAN-Port Based Add interface Vlan Port Based interfaceVLAN-Port Based Edit/Delete interface Use Button to delete the VlanUse Button to modify group name, Vlan ID, or add/remove Members of the existing Vlan group802.1Q Vlan „ Hybrid Link Both Access Link and Trunk Link802.1Q Vlan interface Group Configuration„ You can modify the Vlan group name and Vlan ID Group Configuration interface„ Click Apply button Rapid Spanning Tree Rstp System ConfigurationRstp System Configuration interface Rstp Port ConfigurationRstp Port Configuration interface System Configuration Snmp Configuration„ Community Strings Snmp System Configuration interface Trap ConfigurationUser Profile SNMPV3 Configuration„ Privacy Password Enter the private password Context TableSnmp V3 configuration interface Group Table Access TableMIBview Table „ QoS Policy select the QoS policy rule QoS ConfigurationQoS Policy and Priority Type „ Click Remove to remove an unwanted context namePort-based Priority QoS Configuration interface„ Click Apply button to make the settings effective Igmp ConfigurationCOS Configuration TOS ConfigurationReport Message sent from the querier Igmp router or switchMessage Description QueryRing Ring Interface 802.1x System Configuration interface 802.1X/Radius ConfigurationSecurity 802.1x Per Port Setting interface 802.1x Port Configuration802.1x Misc Configuration interface Misc ConfigurationUse the MAC address table to ensure the port security MAC Address TableMAC Filtering interface Static MAC Addresses interfaceAll MAC Address interface Factory DefaultClick Reboot to reboot the system Save ConfigurationSystem Reboot Click Save to save the configuration to the flash memory101 Trouble shootingMAC address StandardProtocol Transfer RateConsumption Install „ LC Single mode 9/125um Back-planePower Supply PowerIEC60068-2-27 Shock IEC60068-2-6 Vibration SafetyStability testing CE/EN60950-1 IEC60068-2-32 Free fall