B&B Electronics EIR618-2SFP-T manual Dhcp Server System configuration, Dhcp Server Client Entries

Page 66

DHCP Server – System configuration

The switch can function as a DHCP server.

„DHCP Server: Enable or Disable the DHCP Server function.

„Low IP Address: the dynamic IP assign range. Low IP address is the beginning of the dynamic IP assignment range.

„High IP Address: the dynamic IP assign range. High IP address is the end of the dynamic IP assignment range.

„Subnet Mask: The subnet mask.

„Gateway: The network gateway.

„DNS: Network Domain Name Server IP Address.

„Lease Time (sec): The time interval at which that system will reset the dynamic IP assignment.

„Click Apply

DHCP Server Configuration interface

DHCP Server – Client Entries

DHCP Client information is displayed.

54

Manual Documentation Number: EIR618-2SFP-T_5107m

 

 

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax

815-433-5104 – www.bb-elec.com

 

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444

– Fax +353 91-792445 – www.bb-europe.com

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Product Description Page Eighteen Port Managed Industrial Ethernet Switches Kernel Version Firmware VersionV1.07 V2.07FCC Warning Page Content Console Management About Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 101 102Page Features Introduction¾ Port Based Vlan ¾ 802.1 Q Tag Vlan ¾ GvrpPort Trunk with Software SpecificationManagement Spanning treeLogin Security Quality of serviceClass of service Relay AlarmPackage Contents Front Panel Physical DimensionFront Panel of the industrial switch D x H 2.83 x 4.13 x 5.98 in 7.2mm x 10.5mm x 15.2 cmTop Panel of the industrial switch Top ViewLED Indicators Ports Straight Through Cable Schematic Cross Over Cable Schematic „ Gigabit Copper/SFP Mini-GBIC combo portCabling Insert the fiber cable into the transceiver Remove LC connector Wiring the Power Inputs Wiring the Fault Alarm Contact Rear Panel of the switch DIN-Rail DIN-Rail MountingManual Documentation Number EIR618-2SFP-T5107m Panel Mounting Hardware Installation Installation StepsNetwork Application Ring ApplicationCoupling Ring Application Dual Homing Application Pin Assignment Connecting to the Console PortDB9 Connector RJ-45 Connector Orange/White Green/White Blue Blue/White Brown/WhiteLogin in the Console Interface Settings of communication parametersConsole login interface CLI command interfaceCLI Management Commands Level System Name Commands Set ListSystem Commands Set System LocationIp-address PasswordSystem Contact Subnet-maskHours IP addressFull half Port Commands SetPortid 101001000autoEnable Disable ValueTrunk Commands Set Vlan Commands Set GroupIDGroupName Group NamePortNumbers PortNumberSpanning Tree Commands Set ~61440Seconds Forward-time seconds Spanning-treeHello-time seconds Stp-path-costAutoTrueFalse TrueFalseQOS Commands Set Igmp Commands SetMac / Filter Table Commands Set Snmp Commands Set ExactPrifix NameNoAuthNoPrivAuthNoP RivAuthPriv Read View Name Write View Name Notify ViewMibview table Port Mirroring Commands SetRemove specified View Name SNMPV3 agent802.1x Commands Set Port IDWords Disable reject accept SecNumber Tftp Commands Set SystemLog, Smtp and Event Commands SetAuthorize Index Email address ClientserverbothAccount SystemlogSMTPBothSntp Commands Set Start time End timeTimezone Ring Commands SetMinute 1st Ring Port 2nd RingCoupling Port Control PortDual Homing Port About Web-based Management Preparing for Web ManagementSystem Login System Information System information interfaceIP Configuration IP configuration interfaceDhcp Server Client Entries Dhcp Server System configurationDhcp Server Configuration interface Dhcp Client information is displayedDhcp Server Port and IP Bindings Dhcp Client Entries interfacePort and IP Bindings interface Update Firmware interface Tftp Update FirmwareTftp Restore Configuration Restore Configuration interfaceTftp Backup Configuration System Event Log Syslog ConfigurationTftp Server IP Address Enter the Tftp server IP System Event Log Smtp Configuration Syslog Configuration interfaceSystem Event Log Event Configuration Smtp Configuration interfaceEvent Configuration interface Fault Relay Alarm Sntp ConfigurationFault Relay Alarm interface Local Time Zone Conversion from UTC Time at 1200 UTC Switch Timer Displays the current time Click Apply Daylight Saving Offset mins Enter the offset in minutesSntp Configuration interface IP SecurityUser Authentication User Authentication interfaceIP Security interface Port Statistics Port Statistics interfacePort Control Button to add Aggregator settingPort Trunk Port. To remove unwanted ports, select Port and clickDelete to delete Trunk Group Aggregator Information State ActivityDisplays static trunk group information Port Trunk State Activity interface Port Mirroring Port Trunk Port Mirroring interfaceRate Limiting Rate Limiting interfaceVlan configuration Vlan configuration Port-based VlanVlan Configuration interface Vlan Port Based interface VLAN-Port Based Add interfaceMembers of the existing Vlan group Use Button to delete the VlanUse Button to modify group name, Vlan ID, or add/remove VLAN-Port Based Edit/Delete interface„ Hybrid Link Both Access Link and Trunk Link 802.1Q VlanGroup Configuration 802.1Q Vlan interfaceGroup Configuration interface „ You can modify the Vlan group name and Vlan ID„ Click Apply button Rstp System Configuration Rapid Spanning TreeRstp Port Configuration Rstp System Configuration interfaceRstp Port Configuration interface Snmp Configuration System Configuration„ Community Strings Trap Configuration Snmp System Configuration interfaceContext Table SNMPV3 Configuration„ Privacy Password Enter the private password User ProfileSnmp V3 configuration interface Access Table Group TableMIBview Table „ Click Remove to remove an unwanted context name QoS ConfigurationQoS Policy and Priority Type „ QoS Policy select the QoS policy ruleQoS Configuration interface Port-based PriorityTOS Configuration Igmp ConfigurationCOS Configuration „ Click Apply button to make the settings effectiveQuery Message sent from the querier Igmp router or switchMessage Description ReportRing Ring Interface 802.1X/Radius Configuration 802.1x System Configuration interfaceSecurity 802.1x Port Configuration 802.1x Per Port Setting interfaceMisc Configuration 802.1x Misc Configuration interfaceMAC Address Table Use the MAC address table to ensure the port securityStatic MAC Addresses interface MAC Filtering interfaceFactory Default All MAC Address interfaceClick Save to save the configuration to the flash memory Save ConfigurationSystem Reboot Click Reboot to reboot the systemTrouble shooting 101Transfer Rate StandardProtocol MAC addressPower „ LC Single mode 9/125um Back-planePower Supply Consumption InstallCE/EN60950-1 IEC60068-2-32 Free fall SafetyStability testing IEC60068-2-27 Shock IEC60068-2-6 Vibration
Top Page Image Contents