B&B Electronics EIR618-2SFP-T Tftp Backup Configuration, System Event Log Syslog Configuration

Page 69

TFTP - Backup Configuration

You can save current EEPROM image to the TFTP server.

1.TFTP Server IP Address: Enter the TFTP server IP

2.Backup File Name: Enter the file name

3.Click Apply .

Backup Configuration interface

System Event Log – Syslog Configuration

Configure the system event mode to collect system log.

1.Syslog Client Mode: Select the system log mode – client only, server only, or both.

2.System Log Server IP Address: Assigned the system log server IP

3.Click Reload to refresh the event log.

4. Click	Clear	to clear all current event log.

5.After configuring, Click Apply .

Manual Documentation Number: EIR618-2SFP-T_5107m

57

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

Image 69

Contents Product Description Page Eighteen Port Managed Industrial Ethernet Switches V1.07 Firmware VersionKernel Version V2.07FCC Warning Page Content Console Management About Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 102 101Page Introduction Features¾ Gvrp ¾ Port Based Vlan ¾ 802.1 Q Tag VlanManagement Software SpecificationPort Trunk with Spanning treeClass of service Quality of serviceLogin Security Relay AlarmPackage Contents Front Panel of the industrial switch Physical DimensionFront Panel D x H 2.83 x 4.13 x 5.98 in 7.2mm x 10.5mm x 15.2 cmTop View Top Panel of the industrial switchLED Indicators Ports „ Gigabit Copper/SFP Mini-GBIC combo port Straight Through Cable Schematic Cross Over Cable SchematicCabling Insert the fiber cable into the transceiver Remove LC connector Wiring the Power Inputs Wiring the Fault Alarm Contact DIN-Rail Mounting Rear Panel of the switch DIN-RailManual Documentation Number EIR618-2SFP-T5107m Panel Mounting Installation Steps Hardware InstallationRing Application Network ApplicationCoupling Ring Application Dual Homing Application DB9 Connector RJ-45 Connector Connecting to the Console PortPin Assignment Orange/White Green/White Blue Blue/White Brown/WhiteSettings of communication parameters Login in the Console InterfaceConsole login interface CLI command interfaceCLI Management Commands Level System Commands Set Commands Set ListSystem Name System LocationSystem Contact PasswordIp-address Subnet-maskIP address HoursPortid Port Commands SetFull half 101001000autoValue Enable DisableTrunk Commands Set GroupID Vlan Commands SetPortNumbers Group NameGroupName PortNumberSpanning Tree Commands Set ~61440Seconds Hello-time seconds Spanning-treeForward-time seconds Stp-path-costTrueFalse AutoTrueFalseIgmp Commands Set QOS Commands SetMac / Filter Table Commands Set Snmp Commands Set NoAuthNoPrivAuthNoP RivAuthPriv NameExactPrifix Read View Name Write View Name Notify ViewRemove specified Port Mirroring Commands SetMibview table View Name SNMPV3 agent802.1x Commands Set Port IDWords Disable reject accept SecNumber Tftp Commands Set SystemLog, Smtp and Event Commands SetAuthorize Account ClientserverbothIndex Email address SystemlogSMTPBothStart time End time Sntp Commands SetMinute Ring Commands SetTimezone 1st Ring Port 2nd RingCoupling Port Control PortDual Homing Port Preparing for Web Management About Web-based ManagementSystem Login System information interface System InformationIP configuration interface IP ConfigurationDhcp Server Configuration interface Dhcp Server System configurationDhcp Server Client Entries Dhcp Client information is displayedDhcp Server Port and IP Bindings Dhcp Client Entries interfacePort and IP Bindings interface Tftp Restore Configuration Tftp Update FirmwareUpdate Firmware interface Restore Configuration interfaceTftp Backup Configuration System Event Log Syslog ConfigurationTftp Server IP Address Enter the Tftp server IP Syslog Configuration interface System Event Log Smtp ConfigurationSmtp Configuration interface System Event Log Event ConfigurationEvent Configuration interface Fault Relay Alarm Sntp ConfigurationFault Relay Alarm interface Local Time Zone Conversion from UTC Time at 1200 UTC Daylight Saving Offset mins Enter the offset in minutes Switch Timer Displays the current time Click ApplyIP Security Sntp Configuration interfaceUser Authentication User Authentication interfaceIP Security interface Port Statistics interface Port StatisticsPort Control Port Trunk Aggregator settingButton to add Port. To remove unwanted ports, select Port and clickDelete to delete Trunk Group Aggregator Information State ActivityDisplays static trunk group information Port Trunk State Activity interface Port Trunk Port Mirroring interface Port MirroringRate Limiting interface Rate LimitingVlan configuration Vlan configuration Port-based VlanVlan Configuration interface VLAN-Port Based Add interface Vlan Port Based interfaceUse Button to modify group name, Vlan ID, or add/remove Use Button to delete the VlanMembers of the existing Vlan group VLAN-Port Based Edit/Delete interface802.1Q Vlan „ Hybrid Link Both Access Link and Trunk Link802.1Q Vlan interface Group ConfigurationGroup Configuration interface „ You can modify the Vlan group name and Vlan ID„ Click Apply button Rapid Spanning Tree Rstp System ConfigurationRstp System Configuration interface Rstp Port ConfigurationRstp Port Configuration interface Snmp Configuration System Configuration„ Community Strings Snmp System Configuration interface Trap Configuration„ Privacy Password Enter the private password SNMPV3 ConfigurationContext Table User ProfileSnmp V3 configuration interface Access Table Group TableMIBview Table QoS Policy and Priority Type QoS Configuration„ Click Remove to remove an unwanted context name „ QoS Policy select the QoS policy rulePort-based Priority QoS Configuration interfaceCOS Configuration Igmp ConfigurationTOS Configuration „ Click Apply button to make the settings effectiveMessage Description Message sent from the querier Igmp router or switchQuery ReportRing Ring Interface 802.1X/Radius Configuration 802.1x System Configuration interfaceSecurity 802.1x Per Port Setting interface 802.1x Port Configuration802.1x Misc Configuration interface Misc ConfigurationUse the MAC address table to ensure the port security MAC Address TableMAC Filtering interface Static MAC Addresses interfaceAll MAC Address interface Factory DefaultSystem Reboot Save ConfigurationClick Save to save the configuration to the flash memory Click Reboot to reboot the system101 Trouble shootingProtocol StandardTransfer Rate MAC addressPower Supply „ LC Single mode 9/125um Back-planePower Consumption InstallStability testing SafetyCE/EN60950-1 IEC60068-2-32 Free fall IEC60068-2-27 Shock IEC60068-2-6 Vibration