Buffalo Technology WLM2-G54 manual CRC Cyclic Redundancy Check, DCE Data Communications Equip

Page 31

Client: A PC or a workstation on a network.

CRC (Cyclic Redundancy Check):

Calculation method used to check the accuracy of a digital transmission over a communications link.

Cross-Over Wiring: A UTP cable that has its transmit and receive wires crossed to allow communications between two devices.

DCE (Data Communications Equip-

ment): Hardware to be used for communica- tion with a Data Terminal Equipment (DTE) device

Default Gateway:The IP Address of either the nearest router for the LAN or server for the LAN.

Default Parameter: Parameters set by the manufacturer.

Destination Address:The address portion of a packet that identifies the intended recipient station.

DHCP (Dynamic Host Configuration

Protocol): Based on BOOTP, it uses a pool of IP addresses, which it gives out to each device connected to it, and retrieves the addresses when the devices become dormant for a period of time.

DNS (Domain Name System):The on- line distributed database system used to map human-readable machine names into IP addresses. DNS servers throughout the connected Internet implement a hierarchical namespace that allows sites freedom in assigning machine names and addresses. DNS also supports separate mappings between mail destinations and IP addresses.

Driver: A software program that tells an operating system how to use a hardware device.

DSSS (Direct Sequence Spread

Spectrum): A method that spreads the wireless signal into wide frequency bandwidth.

DTE (Data Terminal Equipment): Device

that controls data flowing to or from a computer.

Dynamic IP Address: An IP address that is automatically assigned to a client station in a TCP/IP network, typically by a DHCP server.

ESS (Extended Service Set): A set of two or more BSSs that form a single sub-network.ESS-ID is user identification to be used in the ESS LAN configuration.

Ethernet:The most widely used architecture for Local Area Networks (LANs). It is a shared media network architecture.

Ethernet cable: A wire similar to telephone cable that carries the signals between Ethernet devices.

File and Print Sharing: An application supplied by Microsoft that allows the comput- ers on a network to share files and printers.

Firmware: Programming that is inserted into programmable read-only memory, thus becoming a permanent part of a computing device.

Frame: A frame includes: the data packet, the destination device's address, source device's address, the length of the data packet, and error checking information.

Full-Duplex: Capability for simultaneous transmission in both directions, allowing devices to send & receive data at the same time.

Gbps (Gigabits per second): A measure- ment of billions of bits per second.

Half-duplex:To transmit on the same channel in both directions, one direction at a time.

Hub: A device which allows connection of computers and other devices to form a LAN. When a hub receives packets from a com- puter or other device, it repeats the packets to all of the devices connected to its ports.

IEEE (Institute of Electrical and

Electronics Engineers):The professional organization which promotes development of electronics technology.

IP (Internet Protocol) Address: A unique 32-binary digit number assigned by an Internet authority that identifies each sender or receiver

26

Page 30 Page 32
Image 31
Page 30 Page 32
Contents WLM2-G54 Page Part 10.1 Iii SignsSystem Requirements Summary of FeaturesPackage Contents IntroductionPrivacy FeaturesSecurity Features AuthenticationIbss Security Access AuthorizationIntegrity Features Improved Fault ToleranceNetwork Administration Fea Tures Network Load Distribution FeaturesApartments or Condominiums Easy Support FeaturesNetwork Solutions Typical Office SituationsHospitals SchoolsFactories Area Intranets PoE Power over EthernetSupport Functions Setup Preparation Upgradeable FirmwareDiagnostic Support Client Configuration IntroductionSetup Screen After finding an AirStation, select Admin / Set IP addressInput Parameters Through the Client Manager Input Parameters Through a Wired PC,Terminal SoftwareSelect Start / Run Input Parameters Through a Wired PC,Telnet SoftwareBasic Settings Detailed Configurations IntroductionManagement Time SettingsBridge System1=General administrative informationRouting Server Name=The name of the Radius server or the IP address See next Manual SettingBasic Filter Basic Filter InformationAdd Peer AirStation MAC Address List of the Wireless PCsAuthorized Wireless LAN PCs Wireless11 Link Integrity Settings 10 WirelessPS Privacy Separator Configure EAP in the Security/802.11g screen Privacy, WEPLink Integrity Settings Digits of hexadecimal numbers, i.e. a3d58b62feAdd AirStation Connected AirStation Wireless Distribution System SettingsDiagnostics Introduction Parameters for the Diagnostic Operation3 Wireless LAN PC Information See previous Wireless LAN PC Information5 Ping Test Appendix a Additional InformationAppendix a Intelligent Access Point WLM2-G54 Specifications Table B.1 Diag LED Activity Table Appendix B TroubleshootingOther Problems LED ActivityDTE Data Terminal Equipment Device CRC Cyclic Redundancy CheckDCE Data Communications Equip Dsss Direct Sequence SpreadPCI Peripheral Component Intercon Radius Remote Authentication DialRAM Random Access Memory Non Mips Millions of Instructions PerSnmp Simple Network Management Wlan Wireless LAN a LAN topologyROM Read Only Memory Permanent Smtp Simple Mail Transfer ProtocolPage Page Buffalo Technology Technical Support

WLM2-G54 specifications

Buffalo Technology is known for its high-quality networking products, and one of their standout offerings is the WLM2-G54 wireless LAN router. This device caters to both home and small office users, prioritizing reliability and performance in wireless networking.

The Buffalo WLM2-G54 operates on the IEEE 802.11g standard, providing impressive wireless speeds of up to 54 Mbps. This makes it ideal for activities such as web browsing, streaming videos, and online gaming. Its backward compatibility with older 802.11b devices ensures that users can seamlessly connect their legacy equipment without needing extensive upgrades.

One of the most notable characteristics of the WLM2-G54 is its robust security features. It supports various encryption methods, including WEP, WPA, and WPA2, allowing users to establish secure connections and protect their sensitive data from unauthorized access. The inclusion of a built-in firewall adds another layer of defense, safeguarding the network from external threats.

In terms of physical design, the WLM2-G54 is compact and user-friendly. It can easily fit into small spaces, making it a convenient addition to any home or office setup. The router includes multiple LAN ports for wired connections, ensuring that users can connect additional devices such as desktops, gaming consoles, and printers with ease.

The WLM2-G54 also incorporates advanced technologies to enhance performance. One such feature is Buffalo's "Client Mode," which allows the router to connect to existing networks and extend coverage. This flexibility is beneficial for users who need to bridge long distances or eliminate dead zones in larger spaces.

Another significant characteristic of the WLM2-G54 is its easy setup process. The device typically features a user-friendly web interface, enabling users to configure their network settings without requiring extensive technical knowledge. Additionally, Buffalo often provides firmware updates to improve performance and security, ensuring that users always have access to the latest enhancements.

Overall, Buffalo Technology’s WLM2-G54 wireless LAN router is a versatile, reliable choice for those looking to establish or expand their wireless networking capabilities. With its combination of speed, security, and user-friendly features, it stands out as an excellent option for both home and small office environments. Its ability to integrate with existing network infrastructures further solidifies its place as a valuable asset in modern networking solutions.
Top Page Image Contents