Buffalo Technology WLA-L11 specifications Roaming Function Is Not Operating Correctly

Page 54

Cause (7)

TCP/IP protocol is installed, but the IP address setting is incorrect.

Remedy (7)

Check if the IP address setting is correct.

Refer to the "Allocating IP Addresses" section (page 52) in Chapter 3, Troubleshooting.

Roaming Function Is Not Operating Correctly

Cause

The AirStation settings are incorrect.

Remedy

•Check that the same AirStation group name has been set for all personal computers performing roaming.

•When setting WEP (encryption), set all AirStation WEP settings to the same.

•After enabling the AirStation’s roaming function, reconnect using the wireless LAN personal computer.

Cannot Connect to the AirStation Using Client Manager (Unavailable Even When Found)

Cause (1)

Installation of the wireless LAN card drivers is failed.

Remedy (1)

Refer to the wireless LAN card manual and check if the driver is installed correctly. Also check if the AirStation’s Wireless lamp is lit.

Cause (2)

It is difficult to communicate with the AirStation due to poor radio transmission.

Remedy (2)

Move the wireless LAN personal computer around and making the AirStation closer. Also check if there are obstacles preventing good communications. Remove the obstacles and con- necting again.

Allocating IP Addresses

The following procedure to set the IP address is introduced.

There Is a DHCP Server on the Network (*)

The IP address can be set as follows:

52

WLA-L11 User’s Manual

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Page Symbols Using this ManualPrecaution for the Usage Glossary and Diacritical Marks Within the TextCommunication between a wireless LAN and a wired LAN Setup FlowNetwork Configuration Illustration Table of Contents Glossary Product Specifications Specifications LAN Port Connector SpecificationsInstallation Communications Between Ethernet LAN and Wireless LANOn the Personal Computer Preparing the AirStation SettingsTCP/IP Protocol Setting Windows 98/95Restart Windows 98/95 Select TCP/IP, and then click the Properties buttonAdding TCP/IP Protocols Windows 98/95 Windows Double-click the Local Area Connection iconTo Allocating IP Addresses page 52 Adding the TCP/IP Protocols Windows NectionsCheck if the Internet Protocol TCP/IP is WindowsNT4.0 Adding the TCP/IP Protocol Windows NT Restart Windows NTInstalling AirStation Manager Refer to AirStation Settings Settings Personal Computer AirStation Settings Settings Personal Computer Setting ProcedureLAN card to be used, and then click Settings Completed will be displayed. Close the Web browser Click the Standard Settings buttonWindows 2000/NT Select Edit, and Search AirStationTion of the AirStation setting Connecting To the AirStation Tion Information Files to the diskDrive Try to set the network settings Setting the Wireless LAN Personal ComputerInstalling Client Manager IP is setSelect Client Manager Installation and click Next Click OK. This completes Client Manager AirStation Connection Settings Programs , Melco Wireless LAN , and then Client ManagerChecking AirStation Connection Manager Unavailable Even WhenConnection Test Results Communications notCommunications With Other Personal Computers Double-click the Network Neighborhood icon on the DesktopDouble-click the personal computer you want to connect to What is Next? Displaying AirStation Setting ScreenAirStation Setting What is Next?, and display the AirStation setting screenEnabling and Disabling Roaming Function Programs , Melco Airconnect , and then Client Manager Limiting Connections from Wireless LAN Per Sonal Computers Add MAC Address will be displayed. Click the Return button You can register up to 256 MAC addresses maximumStrengthening Security Using the WEP Encoding Function Multiple AirStation Groups Setting Send Mode Getting Started Setting MethodPersonal Computer Dows personal computerReset the AirStation Setting to the Factory Settings Checking AirStation’s IP AddressChecking the Wireless Frequency Status Connection and DiagnosticConnection Test Result Troubleshooting Check if TCP/IP is correctly installed and set Cable is broken Setting Screen Is Not Displayed Internet Explorer Netscape Navigator 4.0 or Later Start Netscape NavigatorCause Enter the password WEP set in the AirStation Cannot Connect to PCs on the Ethernet LAN TCP/IP Protocol is not installed, or it is not set correctly Windows Roaming Function Is Not Operating Correctly There Is a Dhcp Server on the NetworkWLA-L11 User’s Manual Self-Diagnostic Function Error Details when Diag Lamp FlashesBridge Mode Setting Screen ConfigurationSetting Screens Explanation Detailed Settings Bridge ModeMachine Diagnostics Information of the Main UnitDhcp Server Wireless ChannelMAC Address Media Access Control Address LAN Local Area NetworkWindows 98/95 User Name and Password Windows 98/95 Shared Setting ScreensWEP Encryption Protocol Windows 98/95 Identification ScreenFirmware Displayed ScreenEthernet LAN and Wireless LAN Roaming FunctionProduct Specifications SpecificationsLAN Port Connector Specifications MDI Signal AssignmentMemo Federal Communications Commission Notice PY00-26037-DM10-02
Related manuals
Manual 29 pages 49.89 Kb

WLA-L11 specifications

Buffalo Technology has established itself as a leading provider of networking solutions, and one of their standout products is the WLA-L11. This wireless access point combines advanced features and technologies that make it ideal for both home and office environments.

At the heart of the WLA-L11 is its dual-band capability, allowing for simultaneous connections on both the 2.4 GHz and 5 GHz bands. This dual-band functionality enhances connectivity, enabling users to experience faster speeds and better performance. The 2.4 GHz band is suitable for longer-range connectivity, while the 5 GHz band offers reduced interference and higher speeds, making it perfect for bandwidth-intensive activities like streaming and gaming.

The WLA-L11 supports the latest Wi-Fi 6 (802.11ax) standard, providing significant improvements over previous versions. This technology allows for higher data rates, improved capacity, and better performance in congested environments. With features like OFDMA (Orthogonal Frequency Division Multiple Access) and MU-MIMO (Multi-User Multiple Input Multiple Output), the access point can handle multiple devices simultaneously without sacrificing performance.

Security is a top priority for Buffalo Technology, and the WLA-L11 is no exception. It incorporates advanced encryption protocols, such as WPA3, ensuring that users' data remains secure. Unlike its predecessors, WPA3 offers enhanced protection against brute-force attacks and simplifies the process of connecting new devices.

In terms of physical design, the WLA-L11 boasts a sleek and compact form factor that allows for easy installation in any setting. It can be wall-mounted or placed on a desk, ensuring versatility in deployment. The access point also features Power over Ethernet (PoE) support, which eliminates the need for separate power cables, simplifying installation and reducing clutter.

Additionally, the WLA-L11 is equipped with advanced management capabilities, allowing users to easily configure and monitor their networks. The web-based management interface is user-friendly and provides access to various settings, including bandwidth allocation and guest network creation.

Overall, the Buffalo Technology WLA-L11 stands out for its combination of advanced dual-band Wi-Fi 6 technology, robust security features, and user-friendly design. It is an excellent choice for anyone looking to enhance their wireless networking experience, whether in a home or enterprise environment. With its reliability and performance, the WLA-L11 is set to meet the demands of modern connectivity.
Top Page Image Contents