Briggs & Stratton 50A NEMA 1 owner manual Introduction, For the Installing Dealer/Contractor

Page 4

Briggs & Stratton Power Products Manual Transfer Switch

Installation and Owner’s Manual

INTRODUCTION

Thank you for your purchase of this Briggs & Stratton Power Products Manual Transfer Switch.This product is intended for use with Briggs & Stratton Home Standby Generator sets ONLY.This is an optional home standby system which provides an alternate source of electric power and to serve loads such as heating, refrigeration systems, and communication systems that, when stopped during any power outage, could cause discomfort or the like.This product DOES NOT qualify for emergency standby as defined by NFPA 70 (NEC).

Briggs and Stratton Power Products (BSPP) has made every effort to provide for a safe, streamlined and cost-effective installation. Each installation is unique; it is impossible for BSPP to know and advise of all conceivable procedures and methods by which installation might be performed, nor the potential hazards associated with those methods. For these reasons,

Only licensed electrical contractors should install transfer switches. Installations must strictly comply with all applicable federal, state and local codes, standards and regulations.

Your BSPP Transfer Switch is supplied with this combined “Installation and Owner’s Manual”.This is an important document and should be retained by the owner after the installation has been completed.

Every effort has been expended to make sure that the information in this manual is both accurate and current. However, the manufacturer reserves the right to change, alter or otherwise improve the system at any time without prior notice.

To arrange for proper installation, contact the store at which you purchased your BSPP Transfer Switch, your dealer, or your utility power provider.

The Transfer Switch Warranty is VOID unless the system is installed by a licensed electrical professional.

For the Installing Dealer/Contractor

Check federal, state and local codes for questions on installation.

If you need more information about the transfer switch, call 1-800-743-4115, between 8:00 AM and 5:00 PM CT.

Owner Orientation

The illustrations are for typical circumstances and are meant to familiarize you with the installation options available with your transfer switch.

Local codes, appearance, and distances are the factors that must be considered when negotiating with an installation professional. As the distance from the existing electrical service increases, compensation in wiring materials must be allowed for.This is necessary to comply with local codes and overcome electrical voltage drops.

The factors mentioned above will have a direct effect on the overall price of your transfer switch installation.

NOTE: Your installer must check local codes AND obtain permits before installing the system.

•Read and follow the instructions given in this manual.

•Follow a regular schedule in caring for and using your transfer switch, as specified in the manual.

For the Home or Business Owner

To help you make informed choices and communicate effectively with your installation contractor(s),

Read and understand the

Owner Orientation Section of this manual

BEFORE contracting or starting your transfer switch installation.

Installer Responsibilities

•Read and observe the safety rules.

•Read and follow the instructions given in this manual.

•Check federal, state and local codes.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Installation Table of Contents Safety Rules Only qualified electricians should attempt installationFor the Installing Dealer/Contractor Installer ResponsibilitiesIntroduction Owner OrientationEquipment Description InstallationUnpacking Essential Circuit IsolationPower Wiring Interconnections Mounting GuidelinesModel When Calling the Factory SpecificationsSystem Operation Transfer Switch Service Parts Model 071002 Nema Model 071003 Nema 3RBriggs & Stratton Power Products Manual Transfer Switch Briggs & Stratton Power Products Manual Transfer Switch Limited Warranty Table DES Matières Règles DE Sécurité AvertissementAu Détaillant ou à lEntrepreneur Procédant à lInstallation Responsabilités de lInstallateurIntroduction Au Propriétaire Résidentiel ou CommercialDescription de lÉquipement InstallationDéballage Alimentation de Service Isolation DES Circuits EssentielsInstructions dinstallation Interconnexions du Câblage dAlimentationModèle Fonctionnement DU Système CaractéristiquesSi vous Devez Communiquer avec lUsine Commutateur de transfert homologué UL ModéleRemarques Garantie Limitée Tabla DE Contenido Funcionamiento DEL SistemaAdvertencia Instrucciones DE SeguridadPrecaución Introducción Para el Propietario Comercial o DomésticoOrientación para el Propietario Responsabilidades del InstaladorDescripción del Equipo InstalaciónDesempaque Aislamiento DE LOS Circuitos Fundamentales Interconexiones de Cableado de Energía Instrucciones de MontajeModelo Funcionamiento DEL Sistema EspecificacionesSi Necesita Llamar a Fábrica Interruptor de transferencia UL ModeloGarantía Limitada

50A NEMA 1 specifications

Briggs & Stratton, a renowned name in the power equipment industry, has designed the 50A NEMA 1 panel to offer reliable performance and versatility. This panel is a crucial component for various applications, particularly for those using generators, ensuring efficient distribution of electrical power.

One of the main features of the Briggs & Stratton 50A NEMA 1 is its robust construction. Built to withstand harsh environmental conditions, this panel is enclosed in a durable housing that protects it from dust, moisture, and other external factors that could compromise its functionality. Its NEMA 1 rating indicates that it is designed for indoor use and can tolerate mild levels of exposure to elements, making it a suitable choice for homes and commercial establishments.

Another notable feature of the 50A NEMA 1 is its user-friendly design. The panel is equipped with clearly labeled terminals and an intuitive layout that simplifies the installation and maintenance process. This is particularly beneficial for DIY enthusiasts and professionals alike, as it reduces the likelihood of errors during setup.

The technology integrated into the Briggs & Stratton 50A NEMA 1 enhances its safety and efficiency. It is designed with a circuit breaker that helps protect connected devices from overloads or short circuits. This added layer of protection not only safeguards your equipment but also contributes to the overall longevity of the panel itself.

In terms of characteristics, the 50A capacity of this panel allows it to handle substantial electrical loads. It is an excellent choice for connecting larger generators or multiple appliances, ensuring that all devices receive the proper power supply. This capability is crucial during power outages or emergencies, where reliable power distribution can make a significant difference.

Additionally, the Briggs & Stratton 50A NEMA 1 is compatible with various systems, making it a versatile solution for diverse applications. From residential to commercial use, its adaptability makes it a popular choice among users who require dependable electrical management.

In conclusion, the Briggs & Stratton 50A NEMA 1 panel stands out with its durable construction, user-friendly design, advanced safety technologies, and high capacity for electrical loads. These features combine to create a reliable and efficient solution for managing power distribution, making it an essential asset for any setting that demands consistent and robust electrical performance.
Top Page Image Contents