Dynalink RTA770W user manual Safety Notes

Page 3

ADSL Router User Manual

Safety Notes

For Installation

For Using

For Service

Warning

Caution

Use only the type of power source indicated on the marking labels. Use only power adapter supplied with the product.

Do not overload wall outlet or extension cords as this may increase the risk of electric shock or file. If the power cord is frayed, replace it with a new one.

Proper ventilation is necessary to prevent the product overheating. Do not block or cover the slots and openings on the device, which are intended for ventilation and proper operation. It is recommended to mount the product with a stack.

Do not place the product near any source of heat or expose it to direct sunlight. Do not expose the product to moisture. Never spill any liquid on the product.

Do not attempt to connect with any computer accessory or electronic product without instructions from qualified service personnel. This may result in risk of electronic shock or file.

Do not place this product on an unstable stand or table.

Power off and unplug this product from the wall outlet when it is not in use or before cleaning. Pay attention to the temperature of the power adapter. The temperature might be high.

After powering off the product, power on the product at least 15 seconds later. Do not block the ventilating openings of this product.

When the product is expected to be not in use for a period of time, unplug the power cord of the product to prevent it from the damage of storm or sudden increases in rating.

Do not attempt to disassemble or open covers of this unit by yourself. Nor should you attempt to service the product yourself, which may void the user’s authority to operate it. Contact qualified service personnel under the following conditions:

If the power cord or plug is damaged or frayed. If liquid has been spilled into the product.

If the product has been exposed to rain or water.

If the product does not operate normally when the operating instructions are followed.

If the product has been dropped or the cabinet has been damaged. If the product exhibits a distinct change in performance.

This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.

iii

Image 3
Contents Adsl Router/Modem 000230-rta Safety Notes Page Contents Chapter Vii Viii Adsl Compliance FeaturesATM Features Bridging FeaturesRouting Features Security FeaturesWireless LAN Compliance Features Subscription for Adsl Service Configuration and ManagementUnpacking Xii LED Indicators Physical OutlookFront Panel Diag Rear PanelChoosing a place for the Adsl Router Connecting the Adsl RouterUSB Driver Installation For Windows MEFor Windows For Windows XP Uninstall the USB DriverFor Windows XP Setting TCP/IP on Client PC ConfigurationHighlight Protocol and click Add On IP Address tab Adsl Router User Manaul For Windows ME For Windows NT Configuration Adsl Router User Manaul For Windows Adsl Router User Manaul For Windows XP Configure PC to get IP address from Dhcp Enable Obtain an IP address automatically and then click OK For Windows 98ME Renew IP Address on Client PCFor Windows NT For Windows Using Web-Based Manager Web ConfigurationOutline of Web Manager To Have the New Settings Take EffectConnection Type Quick SetupQuick Start Connect to InternetPPP over ATM/ PPP over Ethernet Leased Time Primary IP AddressSubnet Mask End IP AddressMAC Encapsulated Routing MER Subnet Mask IP over ATM NoneSecondary DNS server Secondary IP Address Bridging Overview StatusAdsl BER Test Adsl LineInternet Connection Traffic StatisticsDhcp Table Wireless Client Routing TableARP Table Apply Advanced SetupLAN- IP Address LAN-DHCP ServerWAN Internet Setting Modulation WAN Adsl SettingsAdding a New One VPI Virtual Path IdentifierRemove Static Route IP Routing Static RouteLocal Router Configuring Other Routers on Your LANAdsl Router EnabledIP Routing Dynamic Routing DNS ServerIP Address seen by Internet Users NAT Virtual ServersCustomized service Select from the following listProtocol Connecting to the Virtual Servers NAT DMZ HostNAT Dynamic DNS User Name: Password: Domain Name: Status: Dynamic DNS:Internet Connection: Firewall IP FilteringSelect the direction to filter packets Allow Traffic Source/Destination IP addressPort Range Igmp Proxy Internet Connection Igmp Proxy EnabledBasic WirelessAdsl Router User Manaul For None WPA WiFi-Protected Access The None itemAuthentication Type SecurityDefault Transmission Key FormatKey 1 to For 802.1X Wireless Network Example for Configuration 802.1x environment For WPA-PSK For WPA Wi-Fi Protected Access Access Control Access ControlMAC Address of Wireless Diagnostics Admin Account Remote AccessManagement Configure System Log Date and TimeSystem Log View System Log button Viewing System LogSnmp Setting Backup Config Update FirmwareReset Router UPnP for XP Web Configuration Adsl Router User Manaul Connection Mode PPP over ATM PPPoA Mode ConfigurationDescription PPP over ATM PPPoA IP Extension Mode Check PPP IP extension then click NextPrimary IP address192.168.1.1 Subnet Mask255.255.255.0 ISP PPP over Ethernet PPPoE ModePPP over Ethernet PPPoE IP Extension Mode MER Numbered IP over ATM IPoA IP Address Subnet Mask Gateway Numbered IP over ATM IPoA+NAT Adsl Router User Manaul Unnumbered IP over ATM IPoA Primary DNS server Secondary DNS serverIP Address Subnet Mask Gateway Unnumbered IP over ATM IPoA+NAT Adsl Router User Manaul Bridge Mode Adsl Router User Manaul Problems with WAN Problems with LANProblems with Upgrading Glossary NAT Network Address Translation IP Address VPI Virtual Path Identifier & VCI Virtual Channel Identifier Adsl Router User Manaul Software SpecificationsVDC Hardware Adsl Router User Manaul Getting Client Certificate Server Setup for 802.1x ClientYes Appendix B Server Setup for 802.1x Client Adsl Router User Manaul
Related manuals
Manual 18 pages 13.82 Kb Manual 16 pages 3.39 Kb

RTA770W, RTA770 specifications

The Dynalink RTA770 is a versatile and powerful router designed to meet the demands of modern home and small business networking. Recognized for its reliability and performance, the RTA770 incorporates advanced technologies that enhance connectivity and overall user experience.

One of the main features of the RTA770 is its dual-band capability, offering simultaneous 2.4 GHz and 5 GHz frequency bands. The dual-band functionality allows for greater flexibility in network connections, reducing interference and optimizing performance. The 2.4 GHz band is ideal for devices like smartphones, tablets, and smart home devices that require a stable signal over longer distances. Conversely, the 5 GHz band caters to bandwidth-intensive activities such as online gaming, streaming high-definition videos, and video conferencing, providing faster speeds with reduced latency.

The RTA770 is equipped with the latest Wi-Fi 6 technology, which significantly boosts speed and efficiency. Wi-Fi 6, also known as 802.11ax, enhances wireless throughput, allowing multiple devices to connect simultaneously without compromising on performance. This is especially beneficial for households with numerous smart devices and users, ensuring a seamless online experience.

Security is a prominent consideration in the design of the RTA770. It features advanced encryption protocols, including WPA3, which offers improved protection against unauthorized access and ensures that personal information remains secure while browsing the internet. The router also supports guest network capability, allowing visitors to access the internet without exposing the primary network.

In terms of connectivity, the RTA770 boasts several ports including Gigabit Ethernet ports that facilitate wired connections for devices such as gaming consoles, smart TVs, and computers. This ensures optimal network performance for devices that require stable connections.

Furthermore, the Dynalink RTA770 includes an easy-to-use web interface for quick setup and management of network settings. Users can conveniently monitor connected devices, configure parental controls, and manage bandwidth allocation.

Overall, the Dynalink RTA770 stands out as a robust networking solution, combining dual-band performance, cutting-edge Wi-Fi 6 technology, enhanced security features, and user-friendly management tools. This makes it a compelling choice for both home users and small businesses looking to improve their network infrastructure.