Multitech MTPSR1-120 manual Enabling SLIP, Dual Ethernet ProxyServer User Guide

Page 38

Enabling SLIP

Dual Ethernet ProxyServer User Guide

Enabling SLIP

If you wish to configure the port for use with SLIP, click on the Enable check box in the SLIP group.

The following message appears:

Click OK. This value was assigned in the initial software installation and was downloaded to the ProxyServer at the end of the installation. If you wish to verify or change the WAN IP address, click on IP in the Firewall Setup menu.

If you wish to make use of CSLIP (Van Jacobsen Compression), click on the CSLIP (Van Jacobsen Compression check box to enable CSLIP. Verify (or change) the Maximum Transmit Unit value (for definition and parameters of a specific field, refer to the on-line help).

By default, Dial On Demand is enabled. If you do not wish to use this feature, click on the Enable check box in the Dial On Demand group to disable it.

When you have finished the configuration, click OK. You are returned to the Firewall Setup menu. Click Download Setup to save the new configuration to the ProxyServer.

38

Image 38

Contents Dual Ethernet ProxyServer Model MTPSR1-120 User GuidePatents User GuideRecord of Revisions RevisionDescription TRADEMARKChapter 1 - Introduction and Description Chapter 2 - InstallationChapter 3 - Software Loading and Configuration Chapter 4 - Firewall SoftwareAppendixes Chapter 5 - Remote Configuration and ManagementChapter 6 - Warranty, Service and Tech Support IndexChapter 1 - Introduction and Description Introduction Chapter 2 - InstallationChapter 3 - Software Loading and Configuration Preview of this GuideChapter 4 - ProxyServer Software Chapter 5 - Remote Configuration and ManagementChapter 6 - Warranty, Service and Tech Support AppendixesETHERNET 1 and PowerFront Panel Description WAN LinkCommand Connector RS232/V.35 ConnectorEthernet 1 and 2 10Base-T Connectors Power ConnectorEthernet Ports SpecificationsCommand Port WAN LinkChapter 2 - Installation Figure 2-1. Unpacking Safety WarningsUnpacking Your ProxyServer Figure 2-2. Cabinet Mounting Screw V.35 Shunt ProcedureStep Procedure Figure 2-3. Shunt PositionsFigure 2-4. Cable Connections Cabling Procedure Step ProcedureCabling Your ProxyServer Chapter 2 - Installation Table 2-1. cont’d Step Procedure Dual Ethernet ProxyServer User Guide Chapter 3 - Software Loading and Configuration Loading Your Software Chapter 3 - Software Loading and Configuration 7. The “Do you want to download default setup?” dialog is displayedIP Port Configuration DHCP Relay Agent does not applyDefault WAN Link Configuration 19. The Writing Setup dialog box is displayed as the setup configuration is written to the ProxyServer Chapter 4 - Firewall Software Typical Applications Configuration 1 - Cable/DSL ModemFigure 4-1. Cable/DSL Modem Configuration Private LANChapter 4 - Firewall Software Internet Services Network Configuration 2 - Existing Dual-LAN with RouterFigure 4-2. Existing Dual-LAN with Router Configuration Private LANConfiguration 3 - New Dual-LAN with T1 DSU Figure 4-3. New Dual-LAN with T1 DSU ConfigurationThe Internet LAN Port Parameters group is either configured with the DHCP Client option active, enabling the ISP to dynamically provide the registered Internet IP addresses, or with the DHCP Client option disabled if a static IP addressing scheme is provided by the ISP. If the DHCP Client field is deactivated the static IP Address of 204.26.12.10 is then entered and the WAN option is checked in the Internet Gateway Parameters group Firewall Program Group Configuration Port SetupDownload Default Setup WAN Device Configuration Download Firmware UpdateUninstall Firewall Configuration Firewall Configuration Changing IP Parameters Net Mask - Enter the Subnetwork Mask for the WAN port in this field Changing WAN Port Parameters Adding Proxy Applications Enabling the DHCP Server Enabling PPP Chapter 5 - Remote Configuration and ManagementEnabling PPP/SLIP Enabling SLIP Applications StatisticsFiltering Chapter 5 - Remote Configuration and Management Modem-Based Remote Configuration Procedure Connect the modem to your local telephone lineClick OK when you are satisfied with your selections LAN-Based Remote Configuration Procedure Windows Sockets Compliant TCP/IP Stack8 Click Exit when the downloading is complete Remote Management TelnetThe Firewall Management Menu provides two basic options Firewall Configuration and WAN Device Configuration. A further option enables you to close the Telnet session from this menu by pressing the Esc key Firewall ConfigurationFirewall Management Menu WEB Management Chapter 6 - Warranty, Service and Tech Support Limited Warranty On-line Warranty RegistrationRecording ProxyServer Information Chapter 6 - Warranty, Service and Technical SupportTech Support MULTI-TECH SYSTEMS, INC 2205 WOODALE DRIVE MOUNDS VIEW, MINNESOTA ServiceATTN SERVICE OR REPAIRS To Download a File The Multi-Tech BBSTo Log on to the Multi-Tech BBS If you know the file nameAbout the Internet About the Multi-Tech Fax-Back ServiceAbout CompuServe ftp//ftp.multitech.comAppendixes Dual Ethernet ProxyServer User Guide Appendix A - TCP/IP Description Internet Protocol IP Index F Secured LAN Port Parameters Configuration 2 - Existing Dual-LAN with Router26Configuration 3 - New Dual-LAN with T1 DSU 20, 33