3Com 1.024.1644-00 Serial transmission, Start/stop bits, Terminal mode, Throughput, 17 Fax

Page 55

Glossary

ROM

Read Only Memory is permanent memory, which is not user- programmable.

serial transmission

The consecutive flow of data in a single channel. Compare to parallel transmissions where data flows simultaneously in multiple channels.

start/stop bits

These signalling bits attached to a character before and after the character is transmitted during asynchronous transmission.

terminal

A device whose keyboard and display are used for sending and receiving data over a communications link. This device differs from a microcomputer or a mainframe in that it has little or no internal processing capabilities.

terminal mode

A software mode that allows direct communication with the modem. This is also known as command mode.

throughput

The amount of actual user data transmitted per second without the overhead of protocol information such as start/stop bits or frame headers and trailers. Compare it with characters per second.

V.8

The ITU-T standard specification that covers the initial handshaking process.

V.17 Fax

An ITU-Tstandard for making facsimile connections at 14400 bps, 12000 bps, 9600 bps, and 7200 bps.

V.21

An ITU-Tstandard for modems operating in asynchronous mode at speeds up to 300 bps, full-duplex, on public switched telephone networks.

56K Voice Faxmodem Internal - User’s Guide

49

Image 55
Contents 56K Voice Faxmodem Internal Page Table of Contents Page Table of Contents Page Welcome to 56K*Information Access Product Features Back Channel Link Rates Upload Speeds Flash ROM Upgradable Control Panel Determining Available ResourcesClick Properties Determining Your Version of WindowsWindows 95 version How to Prepare for Plug and Play Installation Plug and Play InstallationSerial Number How to Insert the Modem into the ComputerPage Page Page Page Moving Through the New Hardware Found Screens Installing Modem Drivers With Windows Versions 950 and 950aPage COM Port Click More Info… Using the Update Device Driver Wizard Screens Installing Modem Drivers With Windows Version 950bPage COM Port Click More Info… Word about COM Ports and IRQs How to Change the Modem’s Settings Page How to Insert the Modem into the Computer Page Page Page Page Restart Now Windows Software InstallationInitialisation String Type of ModemFlow Control Read This First Possible SolutionTroubleshooting Possible Solution Possible Solution Possible Solution Troubleshooting Possible Solution Support Resources Support Resources Are You Still Having Problems?Application Analogue signalsAnswer mode Analogue loopbackGlossary Bit rate Glossary Auto dialBaud rate Binary digit bitClass 1 Data modeGlossary Character Characters per second CPSGlossary DefaultDetect phase Digital signalsFlow control Glossary Error controlFax mode FacsimileOFF/ON hook Local echoModem Nonvolatile memory NvramProtocol Originate modeGlossary Online fallback/fall forward ParityTerminal Terminal modeSerial transmission Start/stop bitsSee online fall back/fall forward 22 bis27ter 32 bisYmodem G 42 bisXmodem YmodemTechnical Reference En Sets local echo Technical ReferenceITU-T answer sequence Dials the specified phone number, includes the followingMn Operates speaker Ln Controls speaker volume internals onlyTechnical Reference Hn Controls ON/OFF hook Displays the following informationVerbal codes Numeric codes11/RINGING Technical Reference Sets result code displayed, default isTechnical Reference Cn Controls Carrier Detect CD signal Resets modemDisplays a list of ampersand & commands An Enables/disables additional result code subsets see XnHn Sets Transmit Data TD flow control see also &Rn Fn Loads a read-only non-programmable factory configurationKn Enables/disables data compression Sets Guard Tone300 bps Sets pulse rotary dial make/break ratio No restrictions on the minimum speed for Yn Sets break handling Wn Writes current configuration to Nvram templates64 56K Voice Faxmodem Internal User’s Guide Registers Register Default FunctionBit Value Result Default FunctionS13 Technical Reference Register Default FunctionTimer S27 See the instructions for S13 S34 Bit +FCLASS=n Sets the mode of operation Fax Commands+FRH=n +FTH=nDisplayed As a number Words Description CE Compliance RegulatoryLimited Warranty