3Com 1.024.1644-00 manual Fax Commands, +FCLASS=n Sets the mode of operation

Page 78

Technical Reference

Fax Commands

+FCLASS=n Sets the mode of operation

FCLASS=0	Data mode
FCLASS=1	Group 3 Facsimile Service Class 1
	mode

FCLASS? Displays the current FCLASS mode (See mode descriptions above)

+FCLASS=? Displays the FCLASS mode options (See mode descriptions above)

+FTS=n Stops the fax transmission. Then the modem waits for a specified time before OK appears on screen. The pause is set in 10 millisecond intervals. n is the number of 10 millisecond intervals that pass before OK appears. (n=0-255)

+FRS=n Makes the modem wait for a specified length of silence before sending OK to the screen. The pause is set in10 millisecond intervals. n is the number of 10 millisecond intervals that pass before OK appears.(n=0-255)

Note: This command terminates with OK when either the specified amount of silence is detected or when the user types anything (which is ignored).

+FTM=n Transmits data using the modulation specified by n.(n = 3, 24, 48, 72, 96, 97, 98, 121, 122, 145, or 146) Note: See the “Screen Messages” table at the end of this section for an explanation of messages that appear in response to this command.

+FRM=n Receives data using the modulation specified by

n.(n = 3, 24, 48, 72, 96, 97, 98, 121, 122, 145, or 146) Note: See the “Screen Messages” table at the end of this section for an explanation of messages that appear in response to this command.

72 56K Voice Faxmodem Internal - User’s Guide

Image 78

Contents 56K Voice Faxmodem Internal Page Table of Contents Page Table of Contents Page Welcome to 56K*Information Access Product Features Back Channel Link Rates Upload Speeds Flash ROM Upgradable Determining Available Resources Control PanelDetermining Your Version of Windows Click PropertiesWindows 95 version Plug and Play Installation How to Prepare for Plug and Play InstallationHow to Insert the Modem into the Computer Serial NumberPage Page Page Page Installing Modem Drivers With Windows Versions 950 and 950a Moving Through the New Hardware Found ScreensPage COM Port Click More Info… Installing Modem Drivers With Windows Version 950b Using the Update Device Driver Wizard ScreensPage COM Port Click More Info… Word about COM Ports and IRQs How to Change the Modem’s Settings Page How to Insert the Modem into the Computer Page Page Page Page Restart Now Software Installation WindowsType of Modem Initialisation StringFlow Control Possible Solution Read This FirstTroubleshooting Possible Solution Possible Solution Possible Solution Troubleshooting Possible Solution Support Resources Are You Still Having Problems? Support ResourcesAnalogue loopback Analogue signalsAnswer mode ApplicationGlossary Binary digit bit Glossary Auto dialBaud rate Bit rateCharacters per second CPS Data modeGlossary Character Class 1Digital signals DefaultDetect phase GlossaryFacsimile Glossary Error controlFax mode Flow controlNonvolatile memory Nvram Local echoModem OFF/ON hookParity Originate modeGlossary Online fallback/fall forward ProtocolStart/stop bits Terminal modeSerial transmission Terminal32 bis 22 bis27ter See online fall back/fall forwardYmodem 42 bisXmodem Ymodem GTechnical Reference Dials the specified phone number, includes the following Technical ReferenceITU-T answer sequence En Sets local echoDisplays the following information Ln Controls speaker volume internals onlyTechnical Reference Hn Controls ON/OFF hook Mn Operates speakerNumeric codes Verbal codesTechnical Reference Sets result code displayed, default is 11/RINGINGTechnical Reference An Enables/disables additional result code subsets see Xn Resets modemDisplays a list of ampersand & commands Cn Controls Carrier Detect CD signalSets Guard Tone Fn Loads a read-only non-programmable factory configurationKn Enables/disables data compression Hn Sets Transmit Data TD flow control see also &Rn300 bps Sets pulse rotary dial make/break ratio No restrictions on the minimum speed for Wn Writes current configuration to Nvram templates Yn Sets break handling64 56K Voice Faxmodem Internal User’s Guide Register Default Function RegistersDefault Function Bit Value ResultTechnical Reference Register Default Function S13Timer S27 See the instructions for S13 S34 Bit Fax Commands +FCLASS=n Sets the mode of operation+FTH=n +FRH=nDisplayed As a number Words Description Regulatory CE ComplianceLimited Warranty