Sierra Wireless MP595W Required equipment, Package contents, Additional required equipment

Page 22

AirLink MP595 / MP595W Modem User Guide

Note: If GPS is being imple- mented, you require either two antennas or a combination Main RF and GPS antenna.

Required equipment

Package contents

Each MP modem box contains:

The MP modem

A mounting template

Mounting screws and washers

An installation and documentation CD

A power harness

If any of these are missing, please contact your account manager.

Additional required equipment

To install the MP modem, you need the power harness (or existing MP 555 Series power harness), or an AC/DC adapter (for office installations), mounting template, and the screws and washers that come with the device.

You may also require:

A USB, Ethernet, or 9‐pin serial cable. This must be long enough to run from the mounting location of the MP modem to the computer.

·The maximum length for the serial or USB cable is 5.5 m (18 feet). The USB cable must have a Type A male connector at the computer end and a Type B male connector at the MP modem end.

·The Ethernet cable should have RJ‐45 connectors. The MP modem’s performance is affected by the type of Ethernet card in the computer and the type of cable used. The minimum requirement for the Ethernet cable is an unshielded twisted pair (UTP) cable, category 3 or 4. For better performance, use a shielded, category 5 cable. The maximum length is 100 m (328 feet).

Main Radio frequency antenna and cable. The antenna must have the appropriate regulatory approval, 50 ohm impedance, and a male TNC connector. It may be a hard or magnetic‐mount antenna.

Access Point antenna and cable. MP 595

Additional Diversity RF antenna (optional). This is required if you use the receive diversity feature. The additional antenna must have a male SMA connector.

GPS antenna and cable (optional). This is necessary if you use the built‐in GPS module.

Power supply. This is usually the vehicle’s battery.

 

 

 

 

 

 

 

22

 

 

 

 

 

2130795

 

 

 

Image 22
Contents User Guide Page Important Notice Safety and Hazards Limitation Liability Patents Copyright Qualcomm 3GContact Information TrademarksRevision History AirLink MP595 / MP595W Modem User Guide 2130795 Contents MP Modem Operation Configuring the Router Functions Support and Warranty Regulatory Information AirLink MP595 / MP595W Modem User Guide 2130795 Introducing the MP Modem About Cdma Cdma account and coverageConnection methods Receive diversitySupported Cdma radio frequencies Virtual serial port VPN support for RnapDocumentation SoftwareMP Modem Manager AirLink MP595 / MP595W Modem User Guide Getting Started Where do you want to install your MP modem? Plan your MP modem installationWhat type of connections do you plan to use? Getting Started Required equipment Package contentsAdditional required equipment MP modem accessories System requirementsAirLink MP595 / MP595W Modem User Guide 2130795 Installation overview Hardware and Software InstallationMP modem housing Overview of installation steps Connector panelGPS and I/O options Select a location for the MP modem Install the MP modemMount the MP modem Mounting the MP modemGround the MP modem Mounting the MP modem. Arrows indicate the mounting holesMount the antennas and install the cables Main RF antennaAP antenna MP 595W only GPS antennaAntenna locations Install the antennas and cables Power connector Molex pinouts Install the power harnessPower connector Vehicle installationIgnition sense on/off wiring Ignition sense optionsCorrect wire splicing Ground the power harnessPower connections Crimp terminalsOffice installation Connect the MP modem to computer cableSerial connector DB9 pinouts Install the USB, Ethernet or serial cableActivate your account Install the softwarePort connections Manual activation Test the systemActivation Wizard Automated activationMP Modem Operation Turning the MP modem on and offStatus indicators LED operation3G Watcher software Reset the MP modem3G Watcher Help Launching 3G Watcher Establishing connections3G Watcher window Configuring the Router Functions NAT modeNon-NAT mode NAT modeMP modem networking basics in NAT ModeSet up static IP addresses Static IP and TCP/UDP port forwarding in NAT modeEnable the router File and resource sharing over LANSet up TCP/UDP port forwarding AirLink MP595 / MP595W Modem User Guide 2130795 Configuring the Wireless Access Point OverviewUnlock MP modem configuration Change the password optionalEnable the wireless access point Set the SsidConfigure the security settings Reset the MP modem to factory defaults Configure security on the client computersAirLink MP595 / MP595W Modem User Guide 2130795 Configuring the MP Modem to Report GPS and I/O Data GPS configuration and reportingGPS protocols and commands GPS display in 3G WatcherDevice installation and configuration GPS Taip quick referencePort specifications Connector pinoutsDigital input devices A button wired to Pin 4 digital input and Pin 10 Ground Example panic button connectionsDigital output devices Analog input devicesConfiguration using AT or 3G Watcher commands Example analog sensor connectionsAnalog input setup ExampleDigital I/O setup AirLink MP595 / MP595W Modem User Guide 2130795 Sending Data to Your Network Application Configure the MP modem toReport frequency timers Route data to a serverTmsumregind Sending Data to Your Network Application Monitoring and Tracking configuration IP AddressingProblem created by Network Address Translation Solutions to the NAT problem Retrieve the Unique Mobile Device IDWarranty Support and WarrantyTechnical support AirLink MP595 / MP595W Modem User Guide 2130795 Technical Specifications Regulatory, radio frequency and electrical specificationsEnvironmental specifications Weight and dimensionsHost interfaces GPS specificationsOther interfaces Port characteristics Wireless access point specificationsWPA2 AirLink MP595 / MP595W Modem User Guide 2130795 Regulatory Information CanadaFCC Caution Important NoteApproved antennas Index NumericsMTP Index AirLink MP595 / MP595W Modem User Guide 2130795

MP595W, MP595 specifications

The Sierra Wireless MP595 and MP595W are robust industrial-grade multi-network routers designed to ensure reliable and high-speed connectivity in a wide range of applications. Both models leverage advanced technologies to meet the demands of IoT (Internet of Things), M2M (Machine-to-Machine), and remote network management, making them ideal for various sectors, including transportation, utility, and smart city initiatives.

One of the standout features of the MP595 and MP595W is their dual-SIM capability. This functionality allows users to connect to two different mobile networks simultaneously, providing added reliability and redundancy. In scenarios where one network experiences failures or inadequate performance, the router can seamlessly switch to the secondary SIM. This ensures continuous connectivity, which is crucial for critical applications where downtime can result in significant losses.

Both models support a full range of cellular technologies, including 4G LTE and 3G, enabling high-speed connections with the flexibility to adapt to different network conditions. The MP595W variant offers additional capabilities, including built-in Wi-Fi, allowing users to set up a local wireless network and connect multiple devices easily.

Furthermore, these routers feature advanced security mechanisms, supporting VPN (Virtual Private Network) protocols and firewall functionalities. This ensures secure data transmission and protects sensitive information from potential threats, making them suitable for enterprise-level applications.

The user-friendly management interface enables easy configuration and monitoring. Sierra Wireless provides comprehensive tools and APIs that facilitate remote management, allowing users to manage and update the router's settings from anywhere, thereby reducing maintenance costs and time.

The routers also come equipped with multiple Ethernet ports, allowing for direct wired connections to equipment and devices. This versatility makes them suitable for a variety of setups, from simple installations to more complex network configurations.

With their rugged design, the MP595 and MP595W are built to withstand harsh environmental conditions, making them perfect for outdoor deployments. They are designed to operate across a wide temperature range, ensuring consistent performance in extreme weather.

In conclusion, the Sierra Wireless MP595 and MP595W are powerful, versatile, and secure solutions for organizations needing robust mobile connectivity. Their advanced features and reliability make them indispensable in achieving seamless communication across various industrial applications.