Sierra Wireless MP595W manual Install the power harness, Power connector Molex pinouts

Page 32

AirLink MP595 / MP595W Modem User Guide

Note: Connector part numbers: 39-01-2040 or 39-01-2045. Pins part number: 39-00-0039.

Step 3—Install the power harness

In a typical installation, the MP modem is connected to the vehicle’s battery with the power harness. The MP modem supports a voltage range between 9 volts direct current (VDC) and 36 VDC, and is designed for both 12 VDC and 24 VDC vehicle electrical systems.

Note: Electrical installations are potentially dangerous and should be performed by personnel thoroughly trained in safe electrical wiring procedures for vehicles.

Power connector

The power harness connects to the MP modem with a Molex connector.

Power connector (Molex) pinouts

The pinouts for the Molex connector on the power harness are:

White wire (Ignition sense)

Unused

Red wire (Battery)

Black wire (Ground)

Figure 3-6: Pinouts for the power harness.

The battery (red) and ignition sense (white) wires in the power harness include 5 A fuses. The black ground wire is not fused. (See “Ground the power harness” on page 34.) Replacement power harnesses are available from Sierra Wireless.

Note: The battery cable used for a car, truck, or other mobile connection must be less than 3 meters in length.

Vehicle installation

This section applies to installing the MP modem in a vehicle. If you are installing it in an office, see “Office installation” on page 35.

 

 

 

 

 

 

 

32

 

 

 

 

 

2130795

 

 

 

Image 32
Contents User Guide Page Important Notice Safety and Hazards Limitation Liability Patents Copyright Qualcomm 3GRevision History TrademarksContact Information AirLink MP595 / MP595W Modem User Guide 2130795 Contents MP Modem Operation Configuring the Router Functions Support and Warranty Regulatory Information AirLink MP595 / MP595W Modem User Guide 2130795 Introducing the MP Modem About Cdma Cdma account and coverageSupported Cdma radio frequencies Receive diversityConnection methods Virtual serial port VPN support for RnapMP Modem Manager SoftwareDocumentation AirLink MP595 / MP595W Modem User Guide Getting Started What type of connections do you plan to use? Plan your MP modem installationWhere do you want to install your MP modem? Getting Started Additional required equipment Package contentsRequired equipment MP modem accessories System requirementsAirLink MP595 / MP595W Modem User Guide 2130795 MP modem housing Hardware and Software InstallationInstallation overview GPS and I/O options Connector panelOverview of installation steps Install the MP modem Mount the MP modemSelect a location for the MP modem Mounting the MP modemGround the MP modem Mounting the MP modem. Arrows indicate the mounting holesMount the antennas and install the cables Main RF antennaAntenna locations GPS antennaAP antenna MP 595W only Install the antennas and cables Install the power harness Power connectorPower connector Molex pinouts Vehicle installationIgnition sense on/off wiring Ignition sense optionsGround the power harness Power connectionsCorrect wire splicing Crimp terminalsOffice installation Connect the MP modem to computer cableSerial connector DB9 pinouts Install the USB, Ethernet or serial cablePort connections Install the softwareActivate your account Test the system Activation WizardManual activation Automated activationMP Modem Operation Turning the MP modem on and offStatus indicators LED operation3G Watcher Help Reset the MP modem3G Watcher software 3G Watcher window Establishing connectionsLaunching 3G Watcher Configuring the Router Functions NAT modeNon-NAT mode NAT modeMP modem networking basics in NAT ModeStatic IP and TCP/UDP port forwarding in NAT mode Enable the routerSet up static IP addresses File and resource sharing over LANSet up TCP/UDP port forwarding AirLink MP595 / MP595W Modem User Guide 2130795 Configuring the Wireless Access Point OverviewUnlock MP modem configuration Change the password optionalEnable the wireless access point Set the SsidConfigure the security settings Reset the MP modem to factory defaults Configure security on the client computersAirLink MP595 / MP595W Modem User Guide 2130795 Configuring the MP Modem to Report GPS and I/O Data GPS configuration and reportingGPS protocols and commands GPS display in 3G WatcherDevice installation and configuration GPS Taip quick referenceDigital input devices Connector pinoutsPort specifications A button wired to Pin 4 digital input and Pin 10 Ground Example panic button connectionsDigital output devices Analog input devicesConfiguration using AT or 3G Watcher commands Example analog sensor connectionsAnalog input setup ExampleDigital I/O setup AirLink MP595 / MP595W Modem User Guide 2130795 Configure the MP modem to Report frequency timersSending Data to Your Network Application Route data to a serverTmsumregind Sending Data to Your Network Application Monitoring and Tracking configuration IP AddressingProblem created by Network Address Translation Solutions to the NAT problem Retrieve the Unique Mobile Device IDTechnical support Support and WarrantyWarranty AirLink MP595 / MP595W Modem User Guide 2130795 Technical Specifications Regulatory, radio frequency and electrical specificationsEnvironmental specifications Weight and dimensionsOther interfaces GPS specificationsHost interfaces Port characteristics Wireless access point specificationsWPA2 AirLink MP595 / MP595W Modem User Guide 2130795 Regulatory Information CanadaApproved antennas Important NoteFCC Caution Index NumericsMTP Index AirLink MP595 / MP595W Modem User Guide 2130795

MP595W, MP595 specifications

The Sierra Wireless MP595 and MP595W are robust industrial-grade multi-network routers designed to ensure reliable and high-speed connectivity in a wide range of applications. Both models leverage advanced technologies to meet the demands of IoT (Internet of Things), M2M (Machine-to-Machine), and remote network management, making them ideal for various sectors, including transportation, utility, and smart city initiatives.

One of the standout features of the MP595 and MP595W is their dual-SIM capability. This functionality allows users to connect to two different mobile networks simultaneously, providing added reliability and redundancy. In scenarios where one network experiences failures or inadequate performance, the router can seamlessly switch to the secondary SIM. This ensures continuous connectivity, which is crucial for critical applications where downtime can result in significant losses.

Both models support a full range of cellular technologies, including 4G LTE and 3G, enabling high-speed connections with the flexibility to adapt to different network conditions. The MP595W variant offers additional capabilities, including built-in Wi-Fi, allowing users to set up a local wireless network and connect multiple devices easily.

Furthermore, these routers feature advanced security mechanisms, supporting VPN (Virtual Private Network) protocols and firewall functionalities. This ensures secure data transmission and protects sensitive information from potential threats, making them suitable for enterprise-level applications.

The user-friendly management interface enables easy configuration and monitoring. Sierra Wireless provides comprehensive tools and APIs that facilitate remote management, allowing users to manage and update the router's settings from anywhere, thereby reducing maintenance costs and time.

The routers also come equipped with multiple Ethernet ports, allowing for direct wired connections to equipment and devices. This versatility makes them suitable for a variety of setups, from simple installations to more complex network configurations.

With their rugged design, the MP595 and MP595W are built to withstand harsh environmental conditions, making them perfect for outdoor deployments. They are designed to operate across a wide temperature range, ensuring consistent performance in extreme weather.

In conclusion, the Sierra Wireless MP595 and MP595W are powerful, versatile, and secure solutions for organizations needing robust mobile connectivity. Their advanced features and reliability make them indispensable in achieving seamless communication across various industrial applications.