Sierra Wireless MP595W manual Ignition sense on/off wiring, Ignition sense options

Page 33

Note: Do not install an on/off switch on the main (red) battery line, or connect the white ignition sense wire to the red battery wire. Both configurations bypass the MP modem's controlled shutdown sequence, and may cause data loss and subsequent power-on problems. Incorrect wiring may also drain the vehicle battery.

Rev 1.4 Draft Mar.08

Hardware and Software Installation

Ignition sense on/off wiring

This section only applies to installing an MP modem in a vehicle. If you are installing the MP modem in an office building, use the AC/DC adapter.

The MP modem’s power on/off is controlled by the ignition sense line (white wire) using internal software, rather than a hard on/off switch on the red power line. The red, black, and white wires connect to the battery and ignition switch as shown in the power harness wiring diagram.

Note: The battery cable used for a car, truck, or other mobile connection must be less than 3 meters in length.

Switch (vehicle

Red wire

5 A fuses (on red

ignition key, or

(Battery)

and white only)

separate)

 

MP modem

 

 

White wire

Black unfused wire

(Ignition sense)

(Ground)

Vehicle battery

Figure 3-7: Wiring for the power harness.The white wire is the ignition sense.

When the white ignition sense line is pulled high (5 to 36 V), the MP modem powers on.

When the ignition sense line is pulled low (less than 2 V), the MP modem performs a controlled shutdown sequence (under software control), de‐registering and saving any relevant operational data before powering off.

Ignition sense options

There are three ways to connect the ignition sense wiring:

Engine on only. Connect the white ignition sense wire to the vehicle’s ignition switch so that the MP modem is powered on only when the ignition key is switched to the full “On” position, that is, when the engine has been started. In this configuration, the engine must be running for the MP modem to be on.

—or—

Accessory on. Connect the white ignition sense wire to the vehicle’s ignition switch so that the MP modem is powered

33

Image 33
Contents User Guide Page Important Notice Safety and Hazards Limitation Liability Qualcomm 3G Patents CopyrightTrademarks Contact InformationRevision History AirLink MP595 / MP595W Modem User Guide 2130795 Contents MP Modem Operation Configuring the Router Functions Support and Warranty Regulatory Information AirLink MP595 / MP595W Modem User Guide 2130795 Introducing the MP Modem Cdma account and coverage About CdmaReceive diversity Connection methodsSupported Cdma radio frequencies VPN support for Rnap Virtual serial portSoftware DocumentationMP Modem Manager AirLink MP595 / MP595W Modem User Guide Getting Started Plan your MP modem installation Where do you want to install your MP modem?What type of connections do you plan to use? Getting Started Package contents Required equipmentAdditional required equipment System requirements MP modem accessoriesAirLink MP595 / MP595W Modem User Guide 2130795 Hardware and Software Installation Installation overviewMP modem housing Connector panel Overview of installation stepsGPS and I/O options Mount the MP modem Install the MP modemSelect a location for the MP modem Mounting the MP modemMounting the MP modem. Arrows indicate the mounting holes Ground the MP modemMain RF antenna Mount the antennas and install the cablesGPS antenna AP antenna MP 595W onlyAntenna locations Install the antennas and cables Power connector Install the power harnessPower connector Molex pinouts Vehicle installationIgnition sense options Ignition sense on/off wiringPower connections Ground the power harnessCorrect wire splicing Crimp terminalsConnect the MP modem to computer cable Office installationInstall the USB, Ethernet or serial cable Serial connector DB9 pinoutsInstall the software Activate your accountPort connections Activation Wizard Test the systemManual activation Automated activationTurning the MP modem on and off MP Modem OperationLED operation Status indicatorsReset the MP modem 3G Watcher software3G Watcher Help Establishing connections Launching 3G Watcher3G Watcher window NAT mode Configuring the Router FunctionsNAT mode Non-NAT modeMode MP modem networking basics in NATEnable the router Static IP and TCP/UDP port forwarding in NAT modeSet up static IP addresses File and resource sharing over LANSet up TCP/UDP port forwarding AirLink MP595 / MP595W Modem User Guide 2130795 Overview Configuring the Wireless Access PointChange the password optional Unlock MP modem configurationSet the Ssid Enable the wireless access pointConfigure the security settings Configure security on the client computers Reset the MP modem to factory defaultsAirLink MP595 / MP595W Modem User Guide 2130795 GPS configuration and reporting Configuring the MP Modem to Report GPS and I/O DataGPS display in 3G Watcher GPS protocols and commandsGPS Taip quick reference Device installation and configurationConnector pinouts Port specificationsDigital input devices Example panic button connections A button wired to Pin 4 digital input and Pin 10 GroundAnalog input devices Digital output devicesExample analog sensor connections Configuration using AT or 3G Watcher commandsExample Analog input setupDigital I/O setup AirLink MP595 / MP595W Modem User Guide 2130795 Report frequency timers Configure the MP modem toSending Data to Your Network Application Route data to a serverTmsumregind Sending Data to Your Network Application IP Addressing Monitoring and Tracking configurationProblem created by Network Address Translation Retrieve the Unique Mobile Device ID Solutions to the NAT problemSupport and Warranty WarrantyTechnical support AirLink MP595 / MP595W Modem User Guide 2130795 Regulatory, radio frequency and electrical specifications Technical SpecificationsWeight and dimensions Environmental specificationsGPS specifications Host interfacesOther interfaces Wireless access point specifications Port characteristicsWPA2 AirLink MP595 / MP595W Modem User Guide 2130795 Canada Regulatory InformationImportant Note FCC CautionApproved antennas Numerics IndexMTP Index AirLink MP595 / MP595W Modem User Guide 2130795

MP595W, MP595 specifications

The Sierra Wireless MP595 and MP595W are robust industrial-grade multi-network routers designed to ensure reliable and high-speed connectivity in a wide range of applications. Both models leverage advanced technologies to meet the demands of IoT (Internet of Things), M2M (Machine-to-Machine), and remote network management, making them ideal for various sectors, including transportation, utility, and smart city initiatives.

One of the standout features of the MP595 and MP595W is their dual-SIM capability. This functionality allows users to connect to two different mobile networks simultaneously, providing added reliability and redundancy. In scenarios where one network experiences failures or inadequate performance, the router can seamlessly switch to the secondary SIM. This ensures continuous connectivity, which is crucial for critical applications where downtime can result in significant losses.

Both models support a full range of cellular technologies, including 4G LTE and 3G, enabling high-speed connections with the flexibility to adapt to different network conditions. The MP595W variant offers additional capabilities, including built-in Wi-Fi, allowing users to set up a local wireless network and connect multiple devices easily.

Furthermore, these routers feature advanced security mechanisms, supporting VPN (Virtual Private Network) protocols and firewall functionalities. This ensures secure data transmission and protects sensitive information from potential threats, making them suitable for enterprise-level applications.

The user-friendly management interface enables easy configuration and monitoring. Sierra Wireless provides comprehensive tools and APIs that facilitate remote management, allowing users to manage and update the router's settings from anywhere, thereby reducing maintenance costs and time.

The routers also come equipped with multiple Ethernet ports, allowing for direct wired connections to equipment and devices. This versatility makes them suitable for a variety of setups, from simple installations to more complex network configurations.

With their rugged design, the MP595 and MP595W are built to withstand harsh environmental conditions, making them perfect for outdoor deployments. They are designed to operate across a wide temperature range, ensuring consistent performance in extreme weather.

In conclusion, the Sierra Wireless MP595 and MP595W are powerful, versatile, and secure solutions for organizations needing robust mobile connectivity. Their advanced features and reliability make them indispensable in achieving seamless communication across various industrial applications.