Telular SX3i Blasting Areas, Potentially Explosive Atmospheres, FCC Part 15 Class B Compliance

Page 23

Safety Information – Continued

Blasting Areas

Construction crews often use remote control RF devices to set off explosives. Therefore, to avoid interfering with blasting oper- ations, turn your Phonecell SX3 OFF when in a "blasting area" or in areas posted: "Turn off two-way radio."

Potentially Explosive Atmospheres

Turn your Phonecell SX3 OFF when in any area with a potentially explosive atmosphere. It is rare, but your Phonecell SX3 or its accessories could generate sparks. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.

Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They include fueling areas such as gas stations; below deck on boats; fuel or chemical transfer or storage facilities; areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn off your vehicle engine.

Do not transport or store flammable gas, liquid or explosives in the area of your Phonecell SX3 or accessories.

Vehicles using liquefied petroleum gas (such as propane or butane) must comply with the National Fire Protection Standard (FPA-58). For a copy of this standard, contact the National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269, Attn: Publications Sales Division.

FCC Part 15 Class B Compliance

This Phonecell SX3 model has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

·Reorient or relocate the antenna.

·Increase the separation between the equipment and the terminal.

·Connect the equipment into an outlet on a circuit different from that to which the terminal is connected.

·Consult your Authorized Telular Distributor or an experienced radio/TV techni- cian for help.

PHONECELL SX3i AMPS

23

USER MANUAL 12/08/99

Image 23
Contents Phonecell SX3i Amps Tel 847-247-9400 · Fax Phones Fax Machine Computer Modem AC PowerIntroduction Table of Contents Un-Packing Your Phonecell SX3i Pre-Installation ChecklistTools & Materials Needed for Wall-Mount Installation Only Getting StartedChoose an Antenna Location pg Installation SummaryCoaxial Cable Choose an Antenna LocationSwitch Antenna Location & SetupHow to Connect the Antenna PowerAdding More Phones? Place a Call Adjust Your FWTPlug In Your Telephone Connect Your TelephoneOdd SID Even SID NAM/Phone Number Setup# * 25 * # # * 4 * # NAM/Phone Number Setup Override Commands# * 24 * # # * 4 * # Press Φ # * 27 * A-Key # Optional A-Key Authentication Code ProgrammingStep #7 How to Override the System Preference Use the following key sequence to program the A-KeyBattery Compartment Batteries Transceiver Optional Battery InstallationDC Port Battery InstallationInstallation is complete PowerMounting Holes Install Your Phonecell5a. Wall-Mount Installation 5b. Desktop/Tabletop Installation Phonecell InstallationPhonecell Operation Fax/Data Transmission How to Adjust the Volume LevelPhonecell Operation Important Tones and Alerts# * 0 * 1 2 3 4 5 6 7 8 # Variable Dial Time Auto Send Delay OptionSpecial Cellular Services Next, press Φ# * 11 * Auto Send Delay #Next, press Φ# * 10 * in-call Dtmf option # Data After Send In-Call Signaling OptionPhonecell SX3 Troubleshooting Safe Operation Requirement Safety InformationAntenna Care and Replacement Exposure to RF Radio Frequency EnergySafety Information FCC Part 15 Class B Compliance Blasting AreasPotentially Explosive Atmospheres Press Φ # * 0 * 1 2 3 4 4 3 2 1 # Amps Technician Programming CommandsHow to Enter the Technician Programming Mode Amps Technician ProgrammingHow to Set the Roam Option Technician Programming CommandsHow to Set the Access Overload Class Accolc How to Set the Access Method EX OptionHow to Restore the Factory Default Settings How to Set the Post-Receiver Off-Hook ROH OptionHow to Set the Pulse Dial Option How to Initiate a Ring-Back Request