RAD Data comm ASMi-31 operation manual Warranty

Page 3

Warranty

This RAD product is warranted against defects in material and workmanship for a period of one year from date of shipment. During the warranty period, RAD will, at its option, either repair or replace products which prove to be defective. For warranty service or repair, this product must be returned to a service facility designated by RAD. Buyer shall prepay shipping charges to RAD and RAD shall pay shipping charges to return the product to Buyer. However, Buyer shall pay all shipping charges, duties and taxes for products returned to RAD from another country.

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by Buyer, Buyer-supplied firmware or interfacing, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper site preparation or maintenance.

Exclusive Remedies

The remedies provided herein are the Buyer's sole and exclusive remedies. RAD shall not be liable for any direct, indirect special, incidental, or consequential damages, whether based on contract, tort, or any legal theory.

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 3
Contents RAD Data Communications Headquarters US East US West ASMi-31Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Warranty Ports Safety Status Safety WarningsRegulatory Information Supplementary Information SafetyAdjust the jumpers see , Installation and Setup Quick Start GuideModem as INT or EXT, and the second modem as RCV Quick Start Guide Contents Card Cage Version List of Figures List of Tables General Power Supply VersionsChapter Introduction OverviewInterfaces Wire twisted pair unconditioned linesControl Signal Transfers DiagnosticsFunctional Description Physical DescriptionManagement ConfigurationsDiagnostic RemoteEthernet 10BT, Ethernet 10B2 BNC Technical SpecificationsTypes ITU V.24/RS-232, V.35, RS-530 or Codirectional 64 kbpsData to the line Master ClockExternal clock The master clock uses Clock derived from the digital interface toEnvironment PhysicalIntroduction Technical Specifications Ambient Chapter Installation and SetupPower Site Requirements and PrerequisitesInstallation and Setup Package ContentsSetting the Internal Jumpers and Switches Opening the ASMi-31 CaseTo open the ASMi-31 case Jumper Description Values Default Setting ASMi-31 PCB Layout ASMi-31 Internal Jumpers and SwitchesLLB, JP15 To close the ASMi-31 case Connecting the LineItem Jumper Description Values Default Setting Closing the ASMi-31 CaseDTE Interfaces and Matching Adapter Cables Connecting the DTEDTE Interface Connector Description RAD Cable To connect the lineConnecting the Power To connect DC power to ASMi-31Refer to DC Power Connection Supplement Chapter Operation Controls and IndicatorsDCD LED is equivalent to Indication signal Front Panel Controls and IndicatorsNormal LEDs ASMi-31 Controls and Indicators Normal OperationOperating Instructions Turning ASMi-31Off Operation Operating Instructions Diagnostic Tests Chapter Troubleshooting and DiagnosticsLocal Analog Loopback LLBTo perform the Local Analog Loopback test To activate the Remote Digital Loopback Remote LoopbackTests and Diagnostics Diagnostic Tests ASM-MN-214 Card Cage Chapter Card Cage VersionASM-MN-214 Rear Panel ASMi-31/R Front Panel ASMi-31/R Card VersionASM-MN-214 Front Panel Power SupplyApplying power, first connect the plug of the power cord to Installing ASMi-31/RTo install the ASMi-31/R card in the ASM-MN-214 card cage ASM-MN-214 card cage has no power switch. Operation startsCard Cage Version Installing ASMi-31/R Appendix a Ethernet Interface GeneralDescription DB-25 IR-ETH Connector OptionsEthernet Bridge Specifications Signal Pin DB-25 RJ-45Protocol Figure A-5 Ethernet Bridge Layout UTP Option Installation and OperationTable A-2 DIP Switches Settings LAN InstallationSwitch Settings LED IndicatorsAppendix A. Ethernet Interface Installation and Operation Appendix B IR-G.703 Codirectional Interface 64 kbps IntroductionGeneral Description Terminal Block RJ-45 DB-25 Standalone Rack Version EXT ModeModem a INT/RCV ModeOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Appendix C Interface Module X.21 ConnectorsTable C-1 Table C-1shows the X.21 DB-15 pin assignmentAppendix C. X.21 Interface Module Figure C-5 INT/RCV Mode Timing Block Figure C-4 EXT Mode Timing BlockTable D-1 Appendix D DTE Interface ConnectorsTable D-1 DTE Interface Signal Assignments Unassigned pins according to X.21 standard Table D-1 DTE Interface Signal Assignments Connecting RS-530 to RS-422 Appendix E Connecting RS-530 to RS-422Table E-1 Connecting RS-530 to RS-422To install a single unit Appendix F Installation in 19 RackInstallation of the ASMi-31 Unit in 19 Rack General Installation of a Single UnitRack see Figure F-2 Figure F-1 Installation of a Single UnitTo install two units Figure F-2 Installation of Two UnitsFigure F-3 Fastening Two Units Together