RAD Data comm ASMi-31 Installation and Operation, Figure A-5 Ethernet Bridge Layout UTP Option

Page 46

Appendix A. Ethernet Interface

ASMi-31Installation and Operation Manual

 

 

 

 

 

 

 

 

 

A.5 Installation and Operation

Figure A-5and Figure A-6show the Ethernet bridge layout, the locations of the DIP switches, and the rear panel components for the UTP and the BNC versions, respectively.

4

3

2

1

Figure A-5 Ethernet Bridge Layout (UTP Option)

4

3

2

1

Figure A-6 Ethernet Bridge Layout (BNC Option)

A-4 Installation and Operation

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 46
Contents ASMi-31 RAD Data Communications Headquarters US East US WestOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Warranty Safety Warnings Ports Safety StatusRegulatory Information Safety Supplementary InformationQuick Start Guide Adjust the jumpers see , Installation and SetupModem as INT or EXT, and the second modem as RCV Quick Start Guide Contents Card Cage Version List of Figures List of Tables Overview Power Supply VersionsChapter Introduction GeneralDiagnostics Wire twisted pair unconditioned linesControl Signal Transfers InterfacesPhysical Description Functional DescriptionRemote ConfigurationsDiagnostic ManagementCodirectional 64 kbps Technical SpecificationsTypes ITU V.24/RS-232, V.35, RS-530 or Ethernet 10BT, Ethernet 10B2 BNCClock derived from the digital interface to Master ClockExternal clock The master clock uses Data to the linePhysical EnvironmentIntroduction Technical Specifications Site Requirements and Prerequisites Chapter Installation and SetupPower AmbientPackage Contents Installation and SetupOpening the ASMi-31 Case Setting the Internal Jumpers and SwitchesTo open the ASMi-31 case ASMi-31 PCB Layout ASMi-31 Internal Jumpers and Switches Jumper Description Values Default SettingLLB, JP15 Closing the ASMi-31 Case Connecting the LineItem Jumper Description Values Default Setting To close the ASMi-31 caseTo connect the line Connecting the DTEDTE Interface Connector Description RAD Cable DTE Interfaces and Matching Adapter CablesTo connect DC power to ASMi-31 Connecting the PowerRefer to DC Power Connection Supplement Front Panel Controls and Indicators Controls and IndicatorsDCD LED is equivalent to Indication signal Chapter OperationTurning ASMi-31 ASMi-31 Controls and Indicators Normal OperationOperating Instructions Normal LEDsOff Operation Operating Instructions Chapter Troubleshooting and Diagnostics Diagnostic TestsLoopback LLB Local AnalogTo perform the Local Analog Loopback test Remote Loopback To activate the Remote Digital LoopbackTests and Diagnostics Diagnostic Tests Chapter Card Cage Version ASM-MN-214 Card CageASM-MN-214 Rear Panel ASMi-31/R Card Version ASMi-31/R Front PanelPower Supply ASM-MN-214 Front PanelASM-MN-214 card cage has no power switch. Operation starts Installing ASMi-31/RTo install the ASMi-31/R card in the ASM-MN-214 card cage Applying power, first connect the plug of the power cord toCard Cage Version Installing ASMi-31/R General Appendix a Ethernet InterfaceDescription IR-ETH Connector Options DB-25Signal Pin DB-25 RJ-45 Ethernet Bridge SpecificationsProtocol Installation and Operation Figure A-5 Ethernet Bridge Layout UTP OptionLED Indicators LAN InstallationSwitch Settings Table A-2 DIP Switches SettingsAppendix A. Ethernet Interface Installation and Operation Introduction Appendix B IR-G.703 Codirectional Interface 64 kbpsGeneral Description EXT Mode Terminal Block RJ-45 DB-25 Standalone Rack VersionINT/RCV Mode Modem aOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 X.21 Connectors Appendix C Interface ModuleTable C-1shows the X.21 DB-15 pin assignment Table C-1Appendix C. X.21 Interface Module Figure C-4 EXT Mode Timing Block Figure C-5 INT/RCV Mode Timing BlockAppendix D DTE Interface Connectors Table D-1Table D-1 DTE Interface Signal Assignments Unassigned pins according to X.21 standard Table D-1 DTE Interface Signal Assignments Appendix E Connecting RS-530 to RS-422 Connecting RS-530 to RS-422Connecting RS-530 to RS-422 Table E-1General Installation of a Single Unit Appendix F Installation in 19 RackInstallation of the ASMi-31 Unit in 19 Rack To install a single unitFigure F-1 Installation of a Single Unit Rack see Figure F-2Figure F-2 Installation of Two Units To install two unitsFigure F-3 Fastening Two Units Together