RAD Data comm operation manual ASMi-31/R Card Version, ASMi-31/R Front Panel

Page 39

ASMi-31Installation and Operation Manual		Chapter 5. Card Cage Version

5.2 ASMi-31/R Card Version

Figure 5-2shows the ASMi-31/R card front panel. The LEDs and switches of the card version are identical in their functionality to those of the standalone device. For this information, refer to Section 3.1, Controls and Indicators, in Chapter 3.

The jumper settings are the same as with ASMi-31 standalone version (refer to Table 2-1).

PWR

RTS

TD

RD

DCD

LOS

ERR

TEST

RESET

ASMi-31

Figure 5-2 ASMi-31/R Front Panel

Power Supply

5-3

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 39

Contents RAD Data Communications Headquarters US East US West ASMi-31Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Warranty Ports Safety Status Safety WarningsRegulatory Information Supplementary Information SafetyAdjust the jumpers see , Installation and Setup Quick Start GuideModem as INT or EXT, and the second modem as RCV Quick Start Guide Contents Card Cage Version List of Figures List of Tables General Power Supply VersionsChapter Introduction OverviewInterfaces Wire twisted pair unconditioned linesControl Signal Transfers DiagnosticsFunctional Description Physical DescriptionManagement ConfigurationsDiagnostic RemoteEthernet 10BT, Ethernet 10B2 BNC Technical SpecificationsTypes ITU V.24/RS-232, V.35, RS-530 or Codirectional 64 kbpsData to the line Master ClockExternal clock The master clock uses Clock derived from the digital interface toEnvironment PhysicalIntroduction Technical Specifications Ambient Chapter Installation and SetupPower Site Requirements and PrerequisitesInstallation and Setup Package ContentsSetting the Internal Jumpers and Switches Opening the ASMi-31 CaseTo open the ASMi-31 case Jumper Description Values Default Setting ASMi-31 PCB Layout ASMi-31 Internal Jumpers and SwitchesLLB, JP15 To close the ASMi-31 case Connecting the LineItem Jumper Description Values Default Setting Closing the ASMi-31 CaseDTE Interfaces and Matching Adapter Cables Connecting the DTEDTE Interface Connector Description RAD Cable To connect the lineConnecting the Power To connect DC power to ASMi-31Refer to DC Power Connection Supplement Chapter Operation Controls and IndicatorsDCD LED is equivalent to Indication signal Front Panel Controls and IndicatorsNormal LEDs ASMi-31 Controls and Indicators Normal OperationOperating Instructions Turning ASMi-31Off Operation Operating Instructions Diagnostic Tests Chapter Troubleshooting and DiagnosticsLocal Analog Loopback LLBTo perform the Local Analog Loopback test To activate the Remote Digital Loopback Remote LoopbackTests and Diagnostics Diagnostic Tests ASM-MN-214 Card Cage Chapter Card Cage VersionASM-MN-214 Rear Panel ASMi-31/R Front Panel ASMi-31/R Card VersionASM-MN-214 Front Panel Power SupplyApplying power, first connect the plug of the power cord to Installing ASMi-31/RTo install the ASMi-31/R card in the ASM-MN-214 card cage ASM-MN-214 card cage has no power switch. Operation startsCard Cage Version Installing ASMi-31/R Appendix a Ethernet Interface GeneralDescription DB-25 IR-ETH Connector OptionsEthernet Bridge Specifications Signal Pin DB-25 RJ-45Protocol Figure A-5 Ethernet Bridge Layout UTP Option Installation and OperationTable A-2 DIP Switches Settings LAN InstallationSwitch Settings LED IndicatorsAppendix A. Ethernet Interface Installation and Operation Appendix B IR-G.703 Codirectional Interface 64 kbps IntroductionGeneral Description Terminal Block RJ-45 DB-25 Standalone Rack Version EXT ModeModem a INT/RCV ModeOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Appendix C Interface Module X.21 ConnectorsTable C-1 Table C-1shows the X.21 DB-15 pin assignmentAppendix C. X.21 Interface Module Figure C-5 INT/RCV Mode Timing Block Figure C-4 EXT Mode Timing BlockTable D-1 Appendix D DTE Interface ConnectorsTable D-1 DTE Interface Signal Assignments Unassigned pins according to X.21 standard Table D-1 DTE Interface Signal Assignments Connecting RS-530 to RS-422 Appendix E Connecting RS-530 to RS-422Table E-1 Connecting RS-530 to RS-422To install a single unit Appendix F Installation in 19 RackInstallation of the ASMi-31 Unit in 19 Rack General Installation of a Single UnitRack see Figure F-2 Figure F-1 Installation of a Single UnitTo install two units Figure F-2 Installation of Two UnitsFigure F-3 Fastening Two Units Together