Sony AR-B1570 manual Halt On, Ega/Vga, Mono

Page 31

AR-B1570 User’s Guide

You have two ways to boot up the system:

1. When VGA as primary and monochrome as secondary, the selection of the video type is “ VGA Mode”.

2When monochrome as primary and VGA as secondary, the selection of the video type is “Monochrome

. Mode”.

EGA/VGA	Enhanced Graphics Adapter/Video Graphics Array. For EGA, VGA, SEGA, or PGA monitor
	adapters
CGA 40	Color Graphics Adapter, power up in 40 column mode
CGA 80	Color Graphics Adapter, power up in 80 column mode
MONO	Monochrome adapter, includes high resolution monochrome adapters

Halt On

This option determines whether the computer will stop if an error is detected during power up.

No errors	The system boot will not be stopped for any error that may be detected.

All errors	Whenever the BIOS detects a non-fatal error the system will be stopped and you will be
	prompted.

All, But	The system boot will not stop for a keyboard error, it will stop for all other errors.
Keyboard
All, But	The system boot will not stop for a disk error, it will stop for all other errors.
Diskette
All, But	The system boot will not stop for a keyboard or disk error, it will stop for all other errors.
Disk/Key

30

Image 31

Contents Industrial Grade CPU Board AR-B1570 User’s Guide Save & Exit Setup Exit Without Saving Preface Organization Static Electricity PrecautionsCPU NS Geode GX1 BGA 1SPECIFICATIONOverview Packing ListAward Bios FeaturesCPU NS Geode GX1 Microprocessor System ControllerDMA Controller Interrupt Controller Keyboard ControllerInterrupt Controller Port Address Map 1 I/O Port Address MapHex Range Device SSDReal-Time Clock & Non-Volatile RAM TimerReal-Time Clock and Non-Volatile RAM Address DescriptionSerial Port Divisor Latch LS, MS Modem Control Register MCRLine Status Register LSR Modem Status Register MSRData Swapper Parallel PortRegister Address Printer Interface LogicBit’s Definition Printer Control Latch & Printer Control SwapperExternal System Location Setting UP the SystemSystem Setting OverviewPin Signal Hard Disk IDE ConnectorPin Hard Disk IDE Connector CN8 Pin Hard Disk IDE Connector CN7Hard Disk IDE1 Connector FDD Port Connector CN3FDD Pin Assignment PS-ON Header CN9 Ethernet RJ-45 Connector LAN14 PS/2 KB/Mouse Connector CN4 & PS1 Reset Header J7P4 CRT Connector Power Connector PWR2CRT Connector P4 LCD Panel Display Connector LCD1Pin Description USB ConnectorUSB1LED Header J8 LCD Display Pin AssignmentPin PC/104 Connector Bus a & B PC104 13 PC104 ConnectorPin PC/104 Connector Bus C & D PC104 15 IR. Header J1 Parallel Port Connector CN216 Ext. Battery CN1 Battery Jumper JP2RS-485 Terminator Select J2 RS-232 Connector Pin Assignment18 COM1, COM2 CN5, CN6 RS-232/RS-485 Select for COM1 P2 & P3ATX Power External Bottom Connector J6 Touch Screen Connector J3 & J420 D.O.C. Memory Address Select JP1 Driver Installation InstallationUtility Diskette Watchdog Block Diagram Watchdog TimerDisk Watchdog Timer Trigger Watchdog Timer SettingIRQ Bios Setup Overview Bios ConsoleBios Setup Main Menu Floppy Setup Standard Cmos SetupDate & Time Setup Hard Disk SetupEGA/VGA Halt OnMono Bios Features Setup Memory Parity Check Typematic Rate SettingTypematic Delay Msec Video Bios ShadowSdram CAS latency Time Chipset Features SetupBit I/O Cycle Recovery Time Chipset Features SetupLoad Setup Defaults PNP/PCI ConfigurationLoad Default Setting Load Bios DefaultsIntegrated Peripherals Bios Exit Password SettingIDE HDD Auto Detection