Philips FW-P78 manual Safety Information

Page 5

GENERAL INFORMATION

IMPORTANT:

PLEASE NOTE THAT THE

VOLTAGE SELECTOR

LOCATED AT THE REAR OF THIS SYSTEM IS PRESET AT 220V FROM THE FACTORY.

FOR COUNTRIES THAT

OPERATE AT 110V, PLEASE

ADJUST TO 110V BEFORE YOU

SWITCH ON THE SYSTEM.

Energy Star

As an ENERGY STARR Partner; Philips has determined that this product meets the ENERGY STARR guidelines for energy efficiency.

SAFETY INFORMATION

Safety Information

• Before operating the system, check that

the operating voltage indicated on the

typeplate (or the voltage indication

beside the voltage selector) of your

system is identical with the voltage of

your local power supply. If not, please

consult your dealer. The typeplate is

located at the rear of your system.

• When the system is switched on, do not

If the system is brought directly from a

 

cold to a warm location, or is placed in a

 

very damp room, moisture may

 

condense on the lens of the CD unit

 

inside the system. Should this occur, the

 

CD player will not operate normally.

 

Leave the power on for about one hour

 

with no disc in the system until normal

 

playback is possible.

Electrostatic discharge may cause

 

unexpected problems. See whether

English

General Information

The type plate (which contains the serial number) is located at the rear of the system.

Recording is permissible if copyright or other rights of third parties are not infringed.

Environmental Information

All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet).

Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Acknowledgement

Dolby Pro-Logic and the double-D symbol dare trademarks of Dolby Laboratories Licensing Corporation.

Manufactured under license from Dolby Laboratories Licensing Corporation.

Accessories (Supplied)

Remote control

Batteries (two AA size) for remote control

AM loop antenna

FM wire antenna

AC power cord

CS-340 speaker package (includes one pair of surround speakers and one center speaker)

 

move it around.

Place the system on a solid base (e.g. a

 

cabinet).

Place the system in a location with

 

adequate ventilation to prevent internal

 

heat build-up in your system. Allow at

 

least 10 cm clearance from the rear and

 

the top of the unit and 5 cm from the

 

each side.

The system incorporates a built-in

 

safety feature that prevents

 

overheating.

Do not expose the system to excessive

 

moisture, rain, sand or heat sources.

Under no circumstances should you

 

repair the system yourself, as this will

 

invalidate the warranty!

these problems disappear if you unplug

the AC power cord and plug it in again

after a few seconds.

• To disconnect the system from the

power supply completely, remove

the AC power plug from the wall

socket.

Untitled-2

5

5

6/8/01, 10:12 AM

3139 116 19782

Image 5
Contents 3139 116 Mini Hi-Fi SystemMinisistema de Audio México110-127/220-240 V ~50-60 Hz Philips Mexicana, S.A. de C.VAustralia/New Zealand/Mexico 106Contents Safety Information Preparation FM Wire Antenna ConnectionAM Loop Antenna Connection Speakers ConnectionAC Power Supply Connecting other Equipment to your systemInserting batteries into Remote Control Rear Surround Speakers’ ConnectionDolby PRO Logic Setting up the Dolby Pro Logic systemDolby Pro Logic Test ToneDolby 3 Stereo Dolby SurroundDolby Center Phantom Normal Stereo3CD ControlsControls on the system and remote control Operating the System Demonstration modeSwitching the system to standby mode Switching the system onEasy Set Selecting the SourceTo switch off DBB For neutral setting, select Classic and switch off DBBMute only on remote control Sound ControlCD Direct Play Discs for playbackLoading the CD Changer Playing a CDSelecting a desired track Disc ChangeProgramming Tracks Reviewing the programErasing the program when Storing Preset Stations Tuning to radio stationsTuning to Preset Radio Stations TunerTape Changing the MW tuning gridLoading a tape Not available for version /30Tape Playback When playback is stoppedRewind/Fast Forward During playbackAUX/CDR There are two Auxiliary modes Normal AUX modeKaraoke Microphone MixingRecording Only å or ∂ mode is available during recordingRecording from other sources It is not possible to change tape side during recordingCD Synchro Start Recording Only å mode is available during dubbingDigital Recording via Digital Out Press Çto stop dubbingTimer Setting TimerClock Setting ClockTimer will not activate if a recording is in progress Sleep TimerTo switch off the Timer To switch off the Sleep TimerSpecifications Maintenance Maintenance TroubleshootingCD Player Operation Radio ReceptionGeneral Tape Deck OperationEnglish