Philips FW-P78 manual Dolby PRO Logic, Test Tone, Setting up the Dolby Pro Logic system

Page 8
TEST TONE

English

DOLBY PRO LOGIC

Dolby Pro Logic

This state of the art Dolby Pro Logic mini system enables you to experience and enjoy a Home Cinema sound ambience. The Pro Logic system allows more accurate definition of the individual sound sources.

Rear (surround) speakers: Connect either the wired rear surround speakers or a pair of wireless rear speakers (not supplied) to the SURROUND OUT terminals.

Center Speaker

For the best sound, place the center speaker at the same height as the left and right speakers. Place the center speaker directly above or beneath the television.

Rear (surround) Speakers

3 Press

 

 

DPL

 

L

 

 

R

BALANCE L

BALANCE

 

 

 

 

 

 

to adjust the

CENTER

 

 

REAR

sound of the

- - +

- - +

front left

 

 

REAR

 

 

 

 

 

speaker.

 

 

 

 

It produces greater sound separation between channels and provides pinpoint sound localization. Pro Logic provides four sound outputs: Left, Center, Right and Surround (Rear). Front sounds are produced from the pair of Left and Right speakers and a Center speaker. The surround sound is reproduced by two speakers placed at the rear of the listening area. Although the

CENTER

REAR

SURROUND

REAR

LEFT

REAR

RIGHT

FRONT

FRONT

LEFT

FRONT

RIGHT

The surround speakers should be placed at normal listening ear level or mounted on the wall at the back of the room. Most important, experiment when placing the surround speakers in order to obtain the best sound.

Test Tone

"BAL L+XX".

4

Press BALANCE R to adjust the sound

 

of the front right speaker.

 

The display will show

 

" BAL R+XX".

5

Press CENTER +or -to adjust the

 

sound of the center speaker.

 

The display will show either

8

surround sound is monaural (single-source), a pair of speakers is necessary to produce the correct diffused sound.

This Pro Logic decoder enables you to decode the following modes: Dolby

Surround, Center Phantom, Dolby 3 Stereo or normal Stereo.

Setting up the Dolby Pro Logic system

You must set up the system properly in order to enjoy the Home Cinema sound to the fullest. First, connect the speakers.

5-Speaker Connection

Front speakers: Connect the front speakers.

Center speaker: Connect the center speaker.

Positioning the Speakers

To get the best surround sound effect, place the speakers as follows.

 

CENTER

 

 

SUB-

SPEAKER

MINI HIFI

 

 

 

FRONT WOOFER

 

SYSTEM

FRONT

LEFT

 

 

RIGHT

 

TV

 

 

SURROUND

 

 

SURROUND

LEFT

 

 

RIGHT

Front Left and Right Speakers

For the best sound, place the Left and Right speakers at an angle of approximately 45 degrees to the listener. If the speakers' magnetic field affects the television picture, increase the distance between the TV and the speakers.

This feature enables you to adjust the Front Left, Front Right, Center and Surround Sound levels of the respective speakers in Dolby Pro Logic mode.

You must sit at the ideal sitting position and use the remote control to perform this operation.

1Press CD, TUNER, TAPE or AUX to switch on the system.

2Press TEST TONE.

A test signal is generated; it will move through the Left, Center, Right, and Surround speakers, in that order.

"TEST TONE" followed by

"ADAPT BALANCE, CENTER AND REAR LEVEL" will be displayed.

The test signal will last for about 90 seconds.

 

"CENT +XX or -XX".

6

Press REAR +or -to adjust the

 

sound of the surround speakers.

 

The display will show either

7

"REAR +XX or -XX".

Adjust the sound of

 

 

all the speakers until

USE

they are equal. When Å you are satisfied with LUME the setting, press

TEST TONE again to É switch off the test signal.

Note:

It is advisable to set the speakers’ level at normal listening level. "XX" denotes the sound level.

Untitled-2

8

6/8/01, 10:12 AM

3139 116 19782

Image 8
Contents Mini Hi-Fi System 3139 116México Minisistema de Audio110-127/220-240 V ~50-60 Hz Philips Mexicana, S.A. de C.V106 Australia/New Zealand/MexicoContents Safety Information FM Wire Antenna Connection PreparationAM Loop Antenna Connection Speakers ConnectionConnecting other Equipment to your system AC Power SupplyInserting batteries into Remote Control Rear Surround Speakers’ ConnectionSetting up the Dolby Pro Logic system Dolby PRO LogicDolby Pro Logic Test ToneDolby Surround Dolby 3 StereoDolby Center Phantom Normal StereoControls 3CDControls on the system and remote control Demonstration mode Operating the SystemSwitching the system on Switching the system to standby modeEasy Set Selecting the SourceFor neutral setting, select Classic and switch off DBB To switch off DBBMute only on remote control Sound ControlDiscs for playback CD Direct PlayLoading the CD Changer Playing a CDDisc Change Selecting a desired trackProgramming Tracks Reviewing the programErasing the program when Tuning to radio stations Storing Preset StationsTuning to Preset Radio Stations TunerChanging the MW tuning grid TapeLoading a tape Not available for version /30When playback is stopped Tape PlaybackRewind/Fast Forward During playbackThere are two Auxiliary modes Normal AUX mode AUX/CDRKaraoke Microphone MixingOnly å or ∂ mode is available during recording RecordingRecording from other sources It is not possible to change tape side during recordingOnly å mode is available during dubbing CD Synchro Start RecordingDigital Recording via Digital Out Press Çto stop dubbingTimer Timer SettingClock Setting ClockSleep Timer Timer will not activate if a recording is in progressTo switch off the Timer To switch off the Sleep TimerSpecifications Maintenance Troubleshooting MaintenanceCD Player Operation Radio ReceptionTape Deck Operation GeneralEnglish