Motion Computing J3400, HC334227332 manual Using Wi-Fi 802.11a/g/n, Using Mobile Broadband optional

Page 60

Using Wi-Fi (802.11a/g/n)

Use the information in this section to set up a Wi-Fi connection. Wireless access requires an 802.11a, 802.11g, or 802.11n access point. Internet access requires a working Internet connection.

DANGER: FAA regulations require that you disable any wireless connection when traveling by air. Failure to disable the wireless connection on the Tablet PC while traveling by air can cause communications problems with aircraft instruments.

Enabling or disabling Wi-Fi

Before you can establish a Wi-Fi connection, you must enable the Wi-Fi adapter. You can enable the Wi-Fi adapter using Motion Dashboard.

To enable or disable Wi-Fi

1.Open the Motion Dashboard to the Wireless panel (page 24).

2.Select or clear the Enable 802.11 Internal Wireless check box.

Setting up a Wi-Fi connection

Use this procedure to create a Wi-Fi connection.

To set up a Wi-Fi connection

1.Open the Motion Dashboard to the Wireless panel (page 24).

2.Ensure that Enable Internal 802.11 Wireless is selected.

3.Tap the Properties button.

4.In the Network and Sharing Center, tap Connect to a network.

5.For Show, select Wireless.

6.Select the network you want to connect to and tap Connect. If you are connecting to a secure network, you may need to enter authentication information.

For more information about Wi-Fi, see “Wi-Fi (802.11a/g/n wireless)” on page 19.

Using Mobile Broadband (optional)

Use the information in this section to set up a Mobile Broadband connection. Mobile Broadband access requires a service contract from a Mobile Broadband service provider.

For more information, see “Mobile Broadband (optional)” on page 20.

WARNING: FAA regulations require that you disable any wireless connection when traveling by air. Failure to disable the wireless connection on the Tablet PC while traveling by air can cause communications problems with aircraft instruments.

54	Chapter 3 Using your Tablet PC

Image 60

Contents User’s Guide AuthenTec is a registered trademark of AuthenTec, Inc Contents Using your Tablet PC Care and Maintenance Appendix a Troubleshooting and Support Getting Started Finding informationOverview Front ViewRear View Right Side Left Side Bottom ViewSetting up the J3400 Plug in the power adapterTo calibrate the digitizer Under Pen & Tablet, tap Calibrate DigitizerGetting Started Features2 Pen Front panel buttons Button Primary Press and hold button For one secondBattery status light Status DescriptionMotion QuickNav To start Motion QuickNavCamera ValueSecurity Windows Security buttonFingerprint reader View Anywhere display optional DisplayMicrophones SpeakersHeadphones port Ambient light sensor ALSMotion DataGuard USB 2.0 portsSecurity slot VGA portEthernet port Docking port Smart card reader slot optionalWi-Fi 802.11a/g/n wireless Express card slot optionalSIM slot Bluetooth wireless optional Power adapterMobile Broadband optional Battery Series FlexDock optionalSeries Mobile Keyboard optional Using your Tablet PC Using Motion Dashboard To start Motion DashboardUsing the Motion utility in the notification area Using the penBattery Health Motion DashboardUsing your Tablet PC Using Tablet PC Input Panel Configuring pen optionsTo configure pen options To start Input PanelUsing personalized handwriting recognition Configuring front panel buttonsConfiguring front panel buttons Using Motion QuickNav Using USBUsing Ethernet Using the camera To use the cameraCamera tips Using the smart card reader optional To insert the smart cardTo remove the smart card Using the Express card reader optional Using the displayAdjusting the display brightness To adjust the display brightnessSetting up an external display To set up an external monitorRotating the display To rotate the displayUsing the built-in microphones Connecting headphones, external speakers, or a microphoneUsing speech recognition Setting up speech recognitionUsing power plans Using Dictation and Voice CommandsSelecting a power plan Changing power plan settings Creating a power planTo change power plan settings To create a power planUsing Sleep Using HibernateTo put your computer on Sleep To put your computer on HibernateUsing the battery Checking battery powerTo check the remaining battery power Charging the battery To check the battery status using the gauge on the batteryBattery and power management tips Removing and replacing the battery Hot Swapping the batteryTo remove the battery To replace the batteryBattery maintenance Long-term battery storage not attached to tabletDisposing of used batteries Removing and replacing the SIM To remove the SIMI M I M To replace the SIMUsing Motion OmniPass and the fingerprint reader Capturing a fingerprintTo start Motion OmniPass To enroll a new user and capture a fingerprintUsing your Tablet PC Using password replacement To register passwordsFingerprint reader tips Tap FinishUsing the password wizard Configuring authentication rulesLogging on to a remembered site Using Windows Security Center Setting up users and passwordsPanel, then tap Windows Security Center Setting up Windows user accounts Setting a Bios passwordSetting up a hard disk drive HDD password To set up a hard disk drive passwordTap Enter for Set Hard Disk Password Using Wi-Fi 802.11a/g/n Using Mobile Broadband optionalEnabling or disabling Wi-Fi Setting up a Wi-Fi connectionUsing Bluetooth optional Activating your Mobile Broadband serviceInstalling the connection manager Connecting and disconnectingEnabling or disabling Bluetooth Setting up a Bluetooth deviceTo enable or disable Bluetooth Select or clear Enable Internal Bluetooth WirelessIf the device is not discovered… Bluetooth wireless tips Finding additional softwareCare and Maintenance General careStandard display Cleaning in a health care environment Disinfecting proceduresTraining and documentation considerations Cleaning the fingerprint reader Cleaning solutionsTo clean the fingerprint reader Replacing pen tips Ordering new pensTo replace the pen tip FAA Wireless air travel requirement Traveling with your Tablet PCTraveling by air Creating a backup archive Using Windows Recovery EnvironmentOn the System Recovery Options menu, click Startup Repair Restoring dataUsing Windows Vista to restore files To restore from your complete PC backup archiveTroubleshooting PowerComputer will not enter Hibernation mode Computer does not turn onBattery DisplayInput Ports and connectors NetworkAudio SystemFrequently asked questions Specifications Warranty and Insurance Programs Service and SupportHow do I adjust the Tablet PC for left-handed use? System InformationAppendix a Troubleshooting and Support Index Page LCD SIM Wireless 80Index