Dell SE500W manual Configuring Resource Dependencies, Setting Advanced Resource Properties

Page 62

w w w . d e l l . c o m s u p p o r t . d e l l . c o m

Configuring Resource Dependencies

Groups function properly only if resource dependencies are configured correctly. The Cluster Service uses the dependencies list when bringing resources online and offline. For example, if a group in which a physical disk and a file share are located is brought online, the physical disk containing the file share must be brought online before the file share.

Table 5-2 shows resources and their dependencies. The resources in the right column must be configured before you create the resource.

Table 5-2. Cluster Resources and Required Dependencies

Resource

Required Dependencies

 

 

File share

Network name (only if configured as a distributed file system [DFS] root)

IP address

None

Network name

IP address that corresponds to the network name

Physical disk

None

 

 

Setting Advanced Resource Properties

You can configure the advanced resource properties using the Advanced tab in the resource Properties dialog box. Use the Advanced tab to have the Cluster Service perform the following tasks:

Restart a resource or allow the resource to fail.

To restart the resource, select Affect the group (if applicable).

To fail over the resource group to another cluster node when the resource fails, select Affect the group and then enter the appropriate values in Threshold and Period. If you do not select Affect the group, the resource group will not fail over to the healthy cluster node.

The Threshold value determines the number of attempts by the Cluster Service to restart the resource before the resource fails over to a healthy cluster node.

The Period value assigns a time requirement for the Threshold value to restart the resource.

Adjust the time parameters for Looks Alive (general check of the resource) or Is Alive (detailed check of the resource) to determine if the resource is in the online state.

Select the default number for the resource type.

To apply the default number, select Use resource type value.

Specify the time parameter for a resource in a pending state (Online Pending or Offline Pending) to resolve its status before moving the resource to Offline or Failed status.

62

Using MSCS

Image 62
Contents Installation and Troubleshooting Guide Abbreviations and Acronyms Contents Naming and Formatting Drives on Assigning Static IP Addresses to Your ClusterUpdating the Windows Driver for the Perc RAID Adapter Microsoft Cluster Administrator Installing and Configuring Microsoft WindowsConfiguring Microsoft Windows Server Configurations Using Non-Dell Products Setting Advanced Resource PropertiesConfiguring Active and Passive Cluster Nodes Uninstalling Mscs From Clusters RunningMaximum Configuration of the PowerEdge Changing the Cluster Service Account PasswordPowerEdge Cluster SE500W Solution Data Form Private Network Hardware Components Power Cabling Example With Two PowerBus Configuration Switch Modes Important System Warning Applications and Hardware RequiringObtaining More Information IntroductionIntended Audience IntroductionQuorum Resource Obtaining Technical Assistance OverviewVirtual Servers and Resource Groups Operating Systems PowerEdge Cluster SE500W SolutionShared Storage Systems Edition X64 Edition Configuration, at least three virtual disks are recommendedStorage System Hardware and Software Technologies Cluster ComponentsSystem Requirements Scsi cablesCluster Node Requirements Component Minimum Requirement Cluster NodesCluster storage Other Documents You May Need Cabling Your Cluster Hardware Cabling for the Cluster SE500W SolutionCabling Your Cluster Hardware Redundant power supply Node Shared storage connector BPin connector Shared storageAdapter Channel 0 Perc RAID adapter channel Pin connectors Pin connectors Cabling Your Cluster HardwareCabling Your Public and Private Networks Network Connections DescriptionCabling Your Public Network Private network adapter Cluster nodePrivate Network Hardware Components and Connections Method Cabling Your Private NetworkNIC Teaming Power Cabling for the PowerEdge Cluster SE500W Solution Cabling the Mouse, Keyboard, and MonitorPage Power Cabling Example With One Power Supply in the Systems Power Cabling Example With Two Power Supplies in the Systems Cabling Your Cluster Hardware Preparing Your Systems for Clustering Preparing Your Systems for ClusteringBefore You Begin Installation Overview Configuring the Cluster Nodes as Domain Controllers Selecting a Domain ModelConfiguring the Internal Drives in Your Cluster Nodes Installing and Configuring the Windows Operating SystemPreparing Your Systems for Clustering Configuring Windows Networking Has been corrected in Windows Server Configuring IP Addresses for the Private NetworkDell recommends using static IP addresses for your cluster Preparing Your Systems for Clustering Configuring the Internet Connection Firewall Verifying Cluster Network CommunicationsInstalling the Perc RAID Adapters Updating the Windows Driver for the Perc RAID AdapterSplit-Bus Module Installing and Configuring the Shared Storage SystemClustering PowerVault Storage Systems Primary Split-bus ModulePage EMM serves two primary functions in your storage system Enclosure Management Module EMMPreparing the Perc RAID Adapter for Clustering Enabling the Cluster Mode Using the Perc RAID Adapter Setting the Scsi Host Adapter IDsConfiguring and Managing Virtual Disks Naming and Formatting Drives on the Shared Storage SystemAssigning Drive Letters and Mount Points EmailData Installing and Configuring Mscs Verifying Cluster ReadinessConfiguring Cluster Networks Running Windows Creating the Quorum ResourceConfiguring Cluster Networks Running Windows Server Preparing Your Systems for Clustering Adding Cluster Nodes Using the Advanced Configuration Option Verifying Mscs Operation Installing Applications in the Cluster GroupVerifying Cluster Functionality Verifying Cluster Resource AvailabilityTroubleshooting Failed Resources Obtaining More InformationLaunching Cluster Administrator on a Cluster Node Installing Your Cluster Management SoftwareMicrosoft Cluster Administrator Running Cluster Administrator on a Remote ConsoleLaunching Cluster Administrator on a Remote Console Cluster Objects Using MscsUsing Mscs Cluster NetworksPreventing Network Failure Network InterfacesCluster Nodes Node-to-Node Communication Forming a New Cluster Joining an Existing ClusterGroups Cluster ResourcesSetting Resource Properties Dependent ResourcesCluster Resources and Required Dependencies Configuring Resource DependenciesSetting Advanced Resource Properties Quorum Disk Quorum Resource Resources and Configurable ParametersResource Parameters Resource Failure Adjusting the Threshold and Period Values Creating a New ResourceDeleting a Resource File Share Resource TypeFailover Configuring Active and Passive Cluster NodesFailover and Failback Using Mscs Failback Using Mscs Upgrading Your System to a Cluster Configuration Certification RequirementsUpgrading Your System to a Cluster Configuration Configurations Using Non-Dell ProductsCompleting the Upgrade Upgrading Your Operating SystemPerforming a Rolling Upgrade Before you perform a rolling upgradeUpgrading Node Maintaining Your Cluster Maintaining Your ClusterAdding a Network Adapter to a Cluster Node IP address Maintaining Your Cluster Removing Nodes From Clusters Running Windows Server Running chkdsk /f on a Quorum DiskRecovering From a Corrupt Quorum Disk Replacing a Cluster-Enabled Dell Perc RAID Adapter Replacing a Cluster NodeWhere clustername is the name of your cluster Reformatting a Cluster Disk Maintaining Your Cluster Rebuilding Operation in Dell OpenManage Utilities Maintaining Your Cluster Maintaining Your Cluster Troubleshooting TroubleshootingPerc 3/DC Bios Troubleshooting Support.microsoft.com Viewer, see the Microsoft Cluster ServiceAdministrator’s Guide for instructions on Troubleshooting Troubleshooting Abbreviations and Acronyms Abbreviations and AcronymsGUI NLB RAM Abbreviations and Acronyms Cluster Data Form PowerEdge Cluster SE500W Solution Data FormCluster Data Form Node Server Type Cluster Name Service Tag Number Server Name System StorageComponent Storage Dell PowerVault Description of Installed ItemsDrive letters, RAID types, applications/data Storage, internal drivesW . d e l l . c o m s u p p o r t . d e l l . c o m Index IndexMscs Virtual disks, 45 using dynamic disks Replacing a cluster-enabledcardShared storage system configuring, 39 enclosure management Index PowerVault 22 xS Back Panel Example of Network Cabling ConnectionPage Table A-1 General Cluster Troubleshooting
Related manuals
Manual 10 pages 46.64 Kb