Acnodes RMC 7189 user manual Rmc

Page 34

RMC 7189

1U Rackmount System

1.After removing the plastic cap, use your thumb and the index finger

to hold the CPU at the north and south center edges.

2.Align the CPU key (the semi-circle cutout) with the socket key (the notch below the gold color dot on the side of the socket).

3.Once the CPU and the socket are aligned, carefully lower the CPU straight down into the socket.

Do not rub the CPU against the surface of the socket or its pins to avoid damaging the CPU or the socket.

4.With the CPU in the socket, in- spect the

four corners of the CPU to make sure that it sits level and is properly installed.

5.Once the CPU is securely seated in the socket, lower the CPU load plate to the socket.

6.Use your thumb to gently push the socket clip down to the clip lock.

Important! Please save the plastic cap. The motherboard must be shipped with the plastic cap properly installed to protect the CPU socket pins. Shipment without the plastic cap properly installed may cause damage to the socket pins.

 

© Copyright 2005 Acnodes, Inc.

661 Brea Canyon Rd., Suite 3

All rights reserved. Product description and product specifications

Walnut, CA 91789

are subject to change without notice. For latest product information,

tel: 909.598.7388, fax: 909.598.0218

please visit Acnodes’ web site at www.acnodes.com.

Page 33 Page 35
Image 34
Page 33 Page 35
Contents RMC Copyright 2005 Acnodes, Inc Preface Manual OrganizationAdvanced Chassis Setup Advanced Motherboard SetupBios Table of Contents Installing the System in to a Rack System InterfaceAdvanced Motherboard Setup Advanced Chassis Setup Introduction OverviewMemory Serverboard FeaturesProcessor Onboard SataServer Chassis Features Cooling System Overview Choosing a Setup LocationPreparing for Setup Unpacking the SystemRack Precautions Server PrecautionsRack Mounting Considerations Installing the System into a Rack Identifying the Sections of the Rack RailsInstalling the Rack Rails Inner RailsOuter Rails RMC Installing the Chassis into a Rack Installing the Server into a Telco Rack Removing the Chassis Cover Figure Checking the Motherboard SetupChecking the Components Checking the Drives Checking the Drive Bay SetupProviding Power Checking the AirflowPower Reset ButtonControl Panel Buttons Control Panel LEDs Universal Information LEDNIC2 HardDrive Carrier LEDs System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Precautions Handling the MotherboardInstalling an LGA1366 Processor Processor and Heatsink InstallationUnpacking RMC Installing the Heatsink Removing the Heatsink Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelI/O Ports Installing DIMMs Installing Memory ModulesMemory Support RMC RMC PCI Card Installation Adding PCI CardsServerboard Details RMC Processor Power Connector Connector DefinitionsATX Power Supply Connector Power LEDHDD LED Power Button Power Fail LEDUniversal Serial Bus Ports Fan Headers Universal Serial Bus HeadersSerial Ports Chassis IntrusionATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/ SpeakerOverheat LED UID Buttons Power SMB I2C ConnectorLAN1/2 Ethernet Ports Explanation of Jumpers Jumper SettingsVGA Enable/Disable Cmos ClearWatch Dog Enable/Disable LAN Enable/DisableSMB to PCI Express Slots ME Mode Select BMC/PHY ResetME Recovery LAN1/2 LEDs Onboard IndicatorsIpmi Dedicated LAN LEDs Sata Port Drive Connections Sata PortsInstalling Software Driver/Tool Installation Display ScreenRMC RMC Static-Sensitive Devices Tools RequiredControl Panel System CoolingSystem Fan Failure Adding a System FanReplacing a System Fan Figure Hard Drive Installation Drive Bay Installation/RemovalAccessing the Drive Bays Installing a Hard Drive into a Drive Carrier FigureRemoving a Hard Drive Figure DVD Drive Installation Power Supply Replacing the Power SupplyRMC How To Change the Configuration Data Starting Bios Setup UtilityIntroduction Main Setup Starting the Setup UtilitySystem Time/System Date System MemoryQuiet Boot Advanced Setup ConfigurationsXboot Features Quick Boot AddOn ROM Display ModePS/2 Mouse Support Wait For F1 If ErrorRestore on AC Power Loss Hit Del Message DisplayXProcessor & Clock Options CPU Ratio Hardware Prefetcher Available when supported by the CPUClock Spread Spectrum Intel Eist Technology State package limit settingActive Processor Cores Intel TurboMode TechnologyXAdvanced Chipset Control Demand Scrubbing Memory ModeMemory Frequency Patrol ScrubbingAir Flow Inlet TemperatureTemperature Rise AltitudeIntel I/OAT Active State Power ManagementNuma Support Slot SXB2/SXB3 WidthXide / Floppy Configuration XPCI/PnP Configuration Load Onboard LAN1 Option ROM/Load Onboard LAN2 Option ROM XSuper IO Device ConfigurationOnboard LAN Option ROM Select Uart 2 of Hermon asXRemote Access Configuration CPU 1 Temperature/ CPU 2 Temperature/ System Temperature XHardware Health ConfigurationCPU Overheat Alarm CPU 1 Temperature/CPU 2 TemperatureFan1 ~ Fan 8 Reading Xacpi Configuration Xipmi Configuration XSet LAN Configuration Clear BMC System Event LogGateway Address XSet PEF ConfigurationBMC Watch Dog Timer Action Mac AddressXEvent Log Configuration User Password Security SettingsSupervisor Password Change Supervisor PasswordPassword Check Change User PasswordBoot Sector Virus Protection XBoot Device Priority Boot SettingsXHard Disk Drives XCD/DVD Drives Exit OptionsXRemovable Drives Save Changes and ExitDiscard Changes and Exit Load Optimal DefaultsLoad Fail-Safe Defaults Discard ChangesAppendix a Post Error Beep Codes Appendix B Installing the Windows Installing Windows OS for a RAID SystemInstalling Windows OS for a Non-RAID Systems Memory Capacity ProcessorsChipset Sata ControllerChassis WeightPower Supply RMC7189 System Cooling

RMC 7189 specifications

The Acnodes RMC 7189 is a powerful and robust industrial computer designed to meet the demanding needs of various applications, ensuring reliable performance in harsh environments. Its rugged construction and advanced features make it a suitable choice for industries such as manufacturing, transportation, and automation.

One of the standout features of the RMC 7189 is its impressive processing capability. Equipped with an Intel Core i7 or i5 processor, it delivers high-performance computing power that can efficiently handle complex tasks and multiple applications simultaneously. The device is designed to support up to 32GB of DDR4 RAM, providing plenty of memory for even the most resource-intensive applications, ensuring smooth operation under load.

The RMC 7189 is designed with versatility in mind. It offers multiple I/O options, including COM ports, USB ports, and Ethernet interfaces, allowing for seamless connectivity with various peripherals and network devices. This flexibility is crucial for integrating the unit into existing systems, enabling it to serve as a central hub for data collection and analysis.

To enhance its durability, the RMC 7189 features a fanless design that minimizes points of failure and reduces noise, making it suitable for environments where traditional cooling methods may be impractical. The system is also resistant to dust and moisture, adhering to IP65 ratings, which makes it ideal for use in factories or outdoor settings.

In terms of storage, the RMC 7189 supports multiple options, including SSDs and HDDs, ensuring that users can choose the appropriate storage solution for their specific applications. The system also includes advanced technologies, such as RAID configurations, to provide data redundancy and protection against hardware failures.

Furthermore, the RMC 7189 is equipped with a range of expansion slots, including PCIe and Mini PCIe, allowing for integration with additional cards and modules, such as GPU for enhanced graphical processing or additional network interfaces to support various communication protocols.

The system supports a wide range of operating systems, including Windows and Linux, providing flexibility for users to choose their preferred platform. This feature, combined with its robust hardware specifications, makes the RMC 7189 a highly adaptable solution for modern industrial challenges.

In summary, the Acnodes RMC 7189 is a highly versatile and powerful industrial computer equipped with advanced features and technologies designed to perform reliably in challenging environments. With its robust construction, extensive connectivity options, and high processing capability, it stands out as an excellent choice for industries aiming to enhance their operational efficiency and data management capabilities.
Top Page Image Contents