Acnodes RMC 7189 user manual XPCI/PnP Configuration

Page 79

RMC 7189

1U Rackmount System

ICH RAID CodeBase (Available if RAID is selected above)

Select Intel to enable Intel's SATA RAID firmware to configure Intel's SATA RAID settings. Select Adaptec to enable Adaptec's SATA RAID firmware to configure Adaptec's SATA RAID settings. The options are Intel and Adaptec.

SATA AHCI (Available if either RAID or AHCI is enabled under"Configure SATA#1 as" above)

Select Enable to enable the function of Serial ATA Advanced Host Interface. (Take caution when using this function. This feature is for advanced program- mers only.)

IDE Detect Timeout (sec)

Use this feature to set the time-out value for the BIOS to detect the ATA, ATAPI devices installed in the system. The options are 0 (sec), 5, 10, 15, 20, 25, 30, and 35.

XPCI/PnP Configuration

This feature allows the user to set the PCI/PnP configurations for the following items:

Clear NVRAM

This feature clears the NVRAM during system boot. The options are No and Yes.

Plug & Play OS

Selecting Yes allows the OS to configure Plug & Play devices. (This is not required for system boot if your system has an OS that supports Plug & Play.) Select No to allow the AMI BIOS to configure all devices in the system.

PCI Latency Timer

This feature sets the latency Timer of each PCI device installed on a PCI bus. Select

64 to set the PCI latency to 64 PCI clock cycles. The options are 32, 64, 96, 128, 160, 192, 224 and 248.

PCI IDE Bus Master

When enabled, the BIOS uses PCI bus mastering for reading/writing to IDE drives. The options are Disabled and Enabled.

PCIe IO Performance

This feature allows the user to configure PCI-E slot settings to enhance perfor- mance. The default setting is 128MB.

PCI SERR Function

PCI SERR (System Error) is for reporting address parity errors, or any other fatal system errors. It is shared among all PCI devices. The options are Disabled and Enabled.

	© Copyright 2009 Acnodes, Inc.
661 Brea Canyon Rd., Suite 3	All rights reserved. Product description and product specifications
Walnut, CA 91789	are subject to change without notice. For latest product information,
tel: 909.598.7388, fax: 909.598.0218	please visit Acnodes’ web site at www.acnodes.com.

Image 79

Contents RMC Copyright 2005 Acnodes, Inc Manual Organization PrefaceAdvanced Chassis Setup Advanced Motherboard SetupBios Table of Contents System Interface Installing the System in to a RackAdvanced Motherboard Setup Advanced Chassis Setup Overview IntroductionOnboard Sata Serverboard FeaturesProcessor MemoryServer Chassis Features Cooling System Unpacking the System Choosing a Setup LocationPreparing for Setup OverviewServer Precautions Rack PrecautionsRack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInner Rails Installing the Rack RailsOuter Rails RMC Installing the Chassis into a Rack Installing the Server into a Telco Rack Removing the Chassis Cover Figure Checking the Motherboard SetupChecking the Components Checking the Airflow Checking the Drive Bay SetupProviding Power Checking the DrivesPower Reset ButtonControl Panel Buttons Universal Information LED Control Panel LEDsNIC2 HardDrive Carrier LEDs Electrical Safety Precautions System SafetyGeneral Safety Precautions ESD Precautions Operating Precautions Handling the Motherboard PrecautionsInstalling an LGA1366 Processor Processor and Heatsink InstallationUnpacking RMC Installing the Heatsink Removing the Heatsink Connecting the Control Panel Connecting CablesConnecting Data Cables Connecting Power CablesI/O Ports Installing DIMMs Installing Memory ModulesMemory Support RMC RMC Adding PCI Cards PCI Card InstallationServerboard Details RMC Power LED Connector DefinitionsATX Power Supply Connector Processor Power ConnectorHDD LED Power Button Power Fail LEDUniversal Serial Bus Ports Chassis Intrusion Universal Serial Bus HeadersSerial Ports Fan HeadersATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/ SpeakerOverheat LED UID Buttons Power SMB I2C ConnectorLAN1/2 Ethernet Ports Cmos Clear Jumper SettingsVGA Enable/Disable Explanation of JumpersWatch Dog Enable/Disable LAN Enable/DisableSMB to PCI Express Slots ME Mode Select BMC/PHY ResetME Recovery LAN1/2 LEDs Onboard IndicatorsIpmi Dedicated LAN LEDs Sata Ports Sata Port Drive ConnectionsDriver/Tool Installation Display Screen Installing SoftwareRMC RMC Tools Required Static-Sensitive DevicesSystem Cooling Control PanelSystem Fan Failure Adding a System FanReplacing a System Fan Figure Installing a Hard Drive into a Drive Carrier Figure Drive Bay Installation/RemovalAccessing the Drive Bays Hard Drive InstallationRemoving a Hard Drive Figure DVD Drive Installation Replacing the Power Supply Power SupplyRMC How To Change the Configuration Data Starting Bios Setup UtilityIntroduction Starting the Setup Utility Main SetupSystem Memory System Time/System DateAddOn ROM Display Mode Advanced Setup ConfigurationsXboot Features Quick Boot Quiet BootHit Del Message Display Wait For F1 If ErrorRestore on AC Power Loss PS/2 Mouse SupportXProcessor & Clock Options CPU Ratio Hardware Prefetcher Available when supported by the CPUClock Spread Spectrum Intel TurboMode Technology State package limit settingActive Processor Cores Intel Eist TechnologyXAdvanced Chipset Control Patrol Scrubbing Memory ModeMemory Frequency Demand Scrubbing Altitude Inlet Temperature Temperature Rise Air FlowSlot SXB2/SXB3 Width Active State Power ManagementNuma Support Intel I/OATXide / Floppy Configuration XPCI/PnP Configuration Uart 2 of Hermon as XSuper IO Device ConfigurationOnboard LAN Option ROM Select Load Onboard LAN1 Option ROM/Load Onboard LAN2 Option ROMXRemote Access Configuration CPU 1 Temperature/CPU 2 Temperature XHardware Health ConfigurationCPU Overheat Alarm CPU 1 Temperature/ CPU 2 Temperature/ System TemperatureFan1 ~ Fan 8 Reading Xacpi Configuration Xipmi Configuration Clear BMC System Event Log XSet LAN ConfigurationMac Address XSet PEF ConfigurationBMC Watch Dog Timer Action Gateway AddressXEvent Log Configuration Change Supervisor Password Security SettingsSupervisor Password User PasswordPassword Check Change User PasswordBoot Sector Virus Protection XBoot Device Priority Boot SettingsXHard Disk Drives Save Changes and Exit Exit OptionsXRemovable Drives XCD/DVD DrivesDiscard Changes Load Optimal DefaultsLoad Fail-Safe Defaults Discard Changes and ExitAppendix a Post Error Beep Codes Installing Windows OS for a RAID System Appendix B Installing the WindowsInstalling Windows OS for a Non-RAID Systems Sata Controller ProcessorsChipset Memory CapacitySystem Cooling WeightPower Supply RMC7189 Chassis