Advantech EKI-1352, EKI-1351 manual Safety Precaution Static Electricity

Page 4

6.Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage.

7.The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS.

8.Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.

9.Position the power cord so that people cannot step on it. Do not place anything over the power cord.

10.All cautions and warnings on the equipment should be noted.

11.If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

12.Never pour any liquid into an opening. This may cause fire or electrical shock.

13.Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14.If one of the following situations arises, get the equipment checked by service personnel:

15.The power cord or plug is damaged.

16.Liquid has penetrated into the equipment.

17.The equipment has been exposed to moisture.

18.The equipment does not work well, or you cannot get it to work according to the user's manual.

19.The equipment has been dropped and damaged.

20.The equipment has obvious signs of breakage.

21.DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

22.CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.

23.The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the products from damage.

„To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on.

„Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive elec- tronic components.

EKI-1351/1352 User Manual

iv

Image 4
Contents EKI-1351/1352 Product Warranty 2 years Copyright AcknowledgementsSafety Instructions Declaration of ConformityTechnical Support and Assistance FCC Class BSafety Precaution Static Electricity Contents Setting COM Redirector Appendix aChapter Introduction Features SpecificationsPackage Check List Getting Started Understanding EKI-1351/1352 Product DescriptionNormal Mode COM Port Redirector Virtual COM PortMulti-Access Mode Shared COM port mode Multi-Access ModeTCP Server Mode TCP Client ModeUDP Server/Client Mode Serial Tunneling ModeControl Mode LED Indicators HardwareDimensions Units mm EKI-1351 and EKI-1352Back View of EKI-1351/1352 Choosing the Location Connecting HardwarePanel/Wall Mounting DIN Rail Mounting 12 DIN-rail StepWireless Connection Power ConnectionSerial Device Server Configuration Utility Serial ConnectionPage Getting Started Page Configuration Configuration Utility Overview Discovering Serial Device Servers Auto SearchingPage Configuration Clear Device List and Search Again Manual AppendingSetting Ethernet Parameters Ethernet BasicWireless Basic Information Wireless BasicsAssociation Information Wireless Basic Settings Site Survey Wireless Authentication Page Wireless Advanced Beacon IntervalSetting Serial Parameters RTS ThresholdFragment Threshold Preamble TypeSetting Serial Port Parameters Setting Virtual COM Operating Mode Parameters Configuration Setting TCP/UDP Server/Client Operating Mode Parameters Configuration Setting Control Operating Mode Parameters AT Commands List Security Configuration Accessible FunctionFulfilling Administrator Functions Port MonitorImport/Export Serial Port Setting Locate Serial DeviceRestore to Factory Default Settings Lock DeviceUpgrading the Firmware Configuration Page Setting COM Redirector Setting COM RedirectorVirtual COM port Auto MappingSetting COM Redirector Manual Mapping Auto Reconnect Property Manual Direct Mapping Virtual COM Port Remove the Virtual COM PortRunning Diagnostic Test Page Appendix a Diagnostic Ad hoc Mode With wireless moduleDiagnostic Infrastructure Mode Without wireless module