Promise Technology TX4, TX8 Array 0 Size 12GB, RAID 0 Functional, Temperature 30C/86F, 5009 RPM

Page 29

VIEW ARRAY INFORMATION

The View Array Information mode displays the array ID, array size, RAID level and array status (Functional, Critical, Offline, Rebuilding and Synchronizing). If these modes of display require more than 2 lines to display information the up and down keys will be used to scroll the display.

The Array ID may be 1, 2, 3, or 4

Array: 0 Size: 12GB	Where the values shown are simply examples.
RAID 0 Functional

RAID 0	Functional
RAID 1	Critical
RAID 3	Rebuilding x%
RAID 5	Offline
RAID 0+1	Synchronizing x%

Array is Functioning properly The array is in a degraded mode Array is rebuilding – x% done Array is down

Array is synchronizing – x% done

What you can do:
Press SEL:		Does nothing.
Press	:	Moves the active message line up.

Press	:	Moves the active message line down.

Press EXIT:		Returns to the View Status mode.

VIEW ENCLOSURE

The View Enclosure menu displays the following information:

Temperature: 30°C/86°F


		FAN 1	: 5009 RPM
		FAN 2	: 4782 RPM
		FAN 3	:	4896 RPM
		FAN 4	:	4983 RPM

Where the values shown are simply examples.

Press or to move these items on the LCD.

What you can do:

Press SEL:

Press :

Press :

Press EXIT:

Does nothing.

Moves the active message line up. Moves the active message line down. Returns to the Configuration mode.

23

Image 29

Contents ULTRATRAK100 TX4 ULTRATRAK100 TX8 Important Data Protection Information CopyrightTrademarks Radio Frequency Interference Statement Table of Contents RAID Page Architectural Description IntroductionFeature Benefit Features and BenefitsConfiguration Install Hard DrivesGetting Started Unpack ULTRATRAK100UltraTrak100 Disk Drive Access TX4 Shown Back of UltraTrak100 TX4 see for TX8 Connecting the Scsi CablesDaisy Chaining Several UltraTrak100s Together Assign a Scsi ID Connect Power Cable and Switch Power onConfigure the ULTRATRAK100 Press SEL to Save Changes Advantages Disadvantages Choosing a RAID LevelRAID 0+1 Characteristics/Advantages DisadvantagesJbod Partition and Format the ArrayDrive Status Indicators MaintenanceIndicator Color Meaning Critical & Offline ArraysReplacing a Disk Drive Module REBUILDING/SYNCHRONIZING Fault Tolerant ArraysWhen a Disk Drive Fails Drive Carrier Drive ReplacementReplacing a Power Supply Module TX8 only Connecting Cables to Disk DriveBack of UltraTrak100 TX8 Type of Interface Name Comments ULTRATRAK100 Front Panel InterfaceConfiguration Mode Error ModeLCD Messages Array FunctionalView Status View Status Configure Array Configure CacheConfigure Scsi View Cache Stats View Controller InfoView Array Information View EnclosureView Controller Information Array 0 Size 12GB Temperature 30C/86FRAID 0 Functional 5009 RPMCreate/Cancel Press SEL to Create Press Exit to Cancel What you can do Auto Array SetupView Drive Assignments Define Array Delete ArrayMaxtor Asng In Ary IBM Asng In Ary No Free Disk What you can doRAID Level 4KB 8KB IBM Assigned Maxtor Free Maxtor FreeWipe out disk Synchronize Array Disable Buzzer Rebuild/Sync Pri. Low Array IDWrite Cache What you can do Write CacheWrite Back Write Thru What you can do Write BackID Selected ModePress Or to move these items on the LCD What you can do Scsi IDContacting Promise Support Technical Support ServicesUSA Tech Support Center European Tech SupportChina Office Pacific Rim Sales OfficeDisclaimer of Other Warranties Limited WarrantyPage Returning Product for Repair USA & Canada Your Responsibilities Introduction to RAID Appendix a Technology BackgroundRAID 1 Mirroring RAID 0+1 STRIPING/MIRROR RAID 3 Block Striping with Parity Drive RAID 5 Block and Parity Striping Jbod Spanning Appendix B Frequently Asked Questions Why can’t I see the drives on the UltraTrak100 under FDISK?