Promise Technology TX4, TX8 user manual Mode, ID Selected

Page 39

Configure SCSI

Mode

ID

LUN

SCSI ID

See below

See page 34

List SCSI IDs 0 thru 15 to be selected from.

CONFIGURE SCSI

The Configure SCSI menu will allow the setting of SCSI parameters. The following parameters are set in the configure SCSI menu:

Mode

SCSI ID

What you can do:

Press SEL:

Selects one of the following active functions:

Mode

 

Move the display to the Mode menu.

SCSI ID

Move the display to the SCSI ID menu.

Press

:

Moves the active message line up. (Active is marked by *.)

 

Press

:

Moves the active message line down. (Active is marked by *.)

 

Press EXIT:

Returns to the Configuration menu.

MODE

Select one of the following SCSI ID modes:

ID Selected

LUN

Selected toggles between these two when SEL is pressed.

What you can do:

Press SEL:

ID

LUN

Press :

Press :

Press EXIT:

Selects one of the following active functions: Select device ID mode.

Select LUN (logical unit number) mode. Moves the active message line up. (Active is marked by *.) Moves the active message line down. (Active is marked by *.) Returns to the Configure SCSI menu.

33

Image 39
Contents ULTRATRAK100 TX4 ULTRATRAK100 TX8 Copyright TrademarksImportant Data Protection Information Radio Frequency Interference Statement Table of Contents RAID Page Architectural Description IntroductionFeature Benefit Features and BenefitsUnpack ULTRATRAK100 Install Hard DrivesConfiguration Getting StartedUltraTrak100 Disk Drive Access TX4 Shown Back of UltraTrak100 TX4 see for TX8 Connecting the Scsi CablesDaisy Chaining Several UltraTrak100s Together Assign a Scsi ID Connect Power Cable and Switch Power onConfigure the ULTRATRAK100 Press SEL to Save Changes Advantages Disadvantages Choosing a RAID LevelRAID 0+1 Characteristics/Advantages DisadvantagesJbod Partition and Format the ArrayCritical & Offline Arrays MaintenanceDrive Status Indicators Indicator Color MeaningREBUILDING/SYNCHRONIZING Fault Tolerant Arrays When a Disk Drive FailsReplacing a Disk Drive Module Drive Carrier Drive ReplacementReplacing a Power Supply Module TX8 only Connecting Cables to Disk DriveBack of UltraTrak100 TX8 Type of Interface Name Comments ULTRATRAK100 Front Panel InterfaceArray Functional Error ModeConfiguration Mode LCD MessagesView Status Configure Array Configure Cache Configure ScsiView Status View Enclosure View Controller InfoView Cache Stats View Array InformationView Controller Information 5009 RPM Temperature 30C/86FArray 0 Size 12GB RAID 0 FunctionalCreate/Cancel Delete Array Auto Array SetupPress SEL to Create Press Exit to Cancel What you can do View Drive Assignments Define ArrayMaxtor Asng In Ary IBM Asng In Ary No Free Disk What you can doRAID Level 4KB 8KB IBM Assigned Maxtor Free Maxtor FreeWipe out disk Synchronize Array Disable Buzzer Rebuild/Sync Pri. Low Array IDWrite Back Write CacheWrite Cache What you can do Write Back Write Thru What you can doID Selected ModePress Or to move these items on the LCD What you can do Scsi IDEuropean Tech Support Technical Support ServicesContacting Promise Support USA Tech Support CenterChina Office Pacific Rim Sales OfficeDisclaimer of Other Warranties Limited WarrantyPage Returning Product for Repair USA & Canada Your Responsibilities Introduction to RAID Appendix a Technology BackgroundRAID 1 Mirroring RAID 0+1 STRIPING/MIRROR RAID 3 Block Striping with Parity Drive RAID 5 Block and Parity Striping Jbod Spanning Appendix B Frequently Asked Questions Why can’t I see the drives on the UltraTrak100 under FDISK?